Other Hardware

Mueller Electric Co - BU-60 series Hardware, Alligator Clips.

Jaw Opening: 0.310" (7.87mm)             

Current Rating (Amps): 10A       

Material: Steel     

Plating: Nickel   

Insulation: Non-Insulated  

Color: Natural

Length: 1.970" (50.04mm)           

Termination: Crimp or Solder

Note: May have a bit of "RUST" from moisture during storage.

Compatible with all shrouded, unshrouded, or retractable 0.16" (4mm) banana plugs, solder or crimp connection, jaw opens 0.31" (7.9 mm) max.

Material: Nickel-plated steel (BU-60).

Length: 1.97" (50mm).

Package of 25.

Learn More

SPC Technology Multicomp - SPC15319 - MBP159 - Connector, Binding Post.

Commercial Quality - Compression Style

Contact Ampacity: 15 Amp.

Insulation Material: Non-insulated.

Accepts 14 AWG Wire 

Contact Plating: Bright Nickel Plated Brass Head and Body.

Mount: Panel Mount

Outside Dimensions: 10mm Diameter,.

Length:  14.30 Closed, 18.80mm Height Extended.

Note: Knurled Knob Screw Actuation. 2.8 x 4.7mm slot for wires.

Mounts from bottom with 6/32 screw (Not Included/ Purchased Separately).

RoHS Compliant

Alternate: Newark 79K4913, 159 HH SMITH

Applications: Instrumentation, Speakers, Laboratory Breadboarding.

Made in Taiwan.

 

Learn More

SOUTHCO - 6-302 - Hardware, Magnetic Door Latch.

Gain a lot of flexibility in applications where you can use these magnetic fastening latches instead of mechanically actuated latches. They are spring loaded for added versativity, are great for light or heavy sheet metal doors and enclosures, tolerate misalignment, and can even be used with non-metallic enclosures by adding a steel strike plate.

A heavy duty magnet 1.23" long x 0.36" thick including steel sides, with a heavy duty spring loaded push button 0.3"square that will push your door open when you push on it.

Will require a mating 1/4" or larger steel tab on door cabinet, when pushed the magnet pulls back.

Dimensions: 3" long x 1" x 0.5" thick.

Materal: Tough Polypropylene 

Mounts with two slots approximately 2.7" apart.

Note: Spring loaded to push open.

New Old Stock

Learn More

Picker International - Marconi - 189564 Hardware, Plexiglass / Acrylic Sheet.

Shatter-resistent or lightweight alternative for glass.

Plexiglas sheet is an excellent electrical insulator with a high dielectric constant.

More Heat thermal shock resisant than glass but also has thermal movement 8 times higher than glass.

Dimensions: 4.5" Square x 0.5" thick.

Clear.

Former Application Manufacturer of advanced medical diagnostic imaging systems.

Learn More

Hardware, hinges. For cabinets or enclosures. Dimensions: 1-3/4" x 2". Package of 10. Learn More

Hardware, Strap Handle.

Heavy Duty Equipment Handle/Strap.

Material: Plastic/Rubber.

Flexible. Dimensions: 1" wide x 6" long.

With Metal/Zinc Support Ends.

Overall length: 7-3/4" long.

P/N: 00383-91-20008.

NOTE: We do NOT include screw harware for mounting.

Alternate/Similar: Reliable Hardware Company RH-0585-A

Learn More

Vintage Phenolic Bakelite Connector, Tie Point/Turret/Connection Board/Terminal/Wiring Strip.

5 Position Dual Row Turret Board

10 Terminals, Double Row of 5 each Turret Board.

Phenolic/Bakelite Fiber Board is 0.100" Thick.

Mount: Chassis Mount

Heavy Duty Turrets are Non-Magnet (Suspect Nickel Plated Brass)

Two 0.150" Diameter Mounting Holes Approximately 1.375" Apart

Dimensions: 2.36" Long x 1.14" Wide x0.46 High.

Vintage - New Old Stock - Bulk Packaged

Proudly Made in USA

Alternate/Similar Compoents: Keystone 15106, 15441, 15111

Applications: Repair / Restoration of Vintage Radio, HIFI, Amplifiers. Project Boards or Electronics Test Equipment.

 

 

 

Learn More

Clear Plastic Socket Covers Learn More

ITW - 4041-00-5075 U-41 - Rubber Bumpers/Feet, Self-adhesive. 1 Sheet

High quality molded rubber Bumper stops are used on thousands of different applications and are made in various shapes and sizes to suit the needs of our customers. These crack-resistant, non-skid bumper pads do not contain plasticizers, oils or fillers. Additionally, they will not mar, scratch, or stain any surface. These bumpers feature an acrylic-based adhesive for long-term adhesion that has excellent solvent and ultraviolet resistance and have high shear strength.

• Abrasion resistant
• Excellent resistance to skidding and coefficient of friction
• Vibration and shock dampening
• Crack-resistant and resilient
• UL-recognized

Each Sheet contains a total of 105 Bumpers = 30 and 75 Self-adhesive Black PVC Round Bumpers

Dimensions: 30 Pieces 0.30" Diameter Tapered, 0.200" High and 75 Pieces Round, Dome Shaped 0.25" Diameter 0.085" High.

Not prepunched, must be cut out of sheet (Approximately 6" x 3").

One sheet of 105 Pieces.

Suggested Applications: Project boxes, under computers desktop calculators keyboards telephones and speakers to prevent vibration skidding or marring surfaces, under cutting boards to prevent skidding, crafts projects and many other uses. 

Proudly Made in USA

Learn More

Dritz - Anchor Hardware. "D" Ring for Straps.

Metal D Rings can be used to make tie downs straps, rigging, carry-on toool or travel bags.

Break Strength - Several Hhundred Pounds.

Material: Steel.

Has a Naval Anchor Stamped on it.

Dimensions: 1.158" wide, 0.87" ID x 0.6"ID.

Also has a Mounting Clip with 0.2" hole.

Color: Chrome Plated.

NOT FOR OVERHEAD LIFTING.

Package of 8.

Learn More

Keystone Electronics - 184 - 30 Volt Battery Holder, Aluminum New

An established design that has gained wide acceptance for commercial and military applications. Batteries are held under constant spring tension assuring low contact resistance. Recommended for use where shock or severe vibration is encountered. 

Clips: Spring Steel, Nickel Plate

Phenolic Base: Type PBE, Per MIL-P-3115C

Contact Eyelets: Brass, Nickel Plate

Frame and Clips: Aluminum 2024-T3

Insulating Washers: Moisture Proof, Resin Impregnated Fibre

Solder Lugs: Brass, Tin Plate

Numer of Cells: 2

Mounting Type: Chassis Mount

Termination Style: Solder Lugs

Battery Cell Size: 2/3A

Battery Holder Dimensions: See Attached Illustration.

Two mounting holes on Bottom 1.912" Spacing.

Chassis Mount.

Solder Lug Terminals.

Heavy Duty - New Old Stock.

Made in USA

Battery Cross Reference: Eveready 413, NEDA 210 

Alternates: Digi-Key 36-184-ND, Mouser 534-184, Newark 35F1638

Learn More

Hardware, Bracket. 4 Slot.

Material: steel, gray.

Dimensions: 4-3/16" long x 3-1/2" wide x 1/2" high, plus mount flange each end (3-1/8" l x 1/2" wide with 2 hole mt @ 2-1/4" centers).

Learn More

Hardware. Shock mount 2-1/2" square.

Learn More

General Electric - CR215DBX02 - Threaded Barrel Proximity Switch Accessory

18mm Mounting Bracket

Made in USA

Learn More

Bivar Inc - 126-040 Hardware, Spacers.

Perm-O-Pads series, TO-5 to TO-18, T1-3/4 LED, Universal, 4 lead, with Open Center.

Material: Nylon 6/6 94V-2

Description: 0.040 wide x 0.040 long x 0.04 thick. (Ref. Attached Diaagram)

Color: White.

Package of 50.

 

Learn More

SPACER HARDWARE KIT Slidelock Leaded Process Compatible:No Peak Reflow Compatible (260 C):No Learn More

Hardware, kit. Tinnerman mounting kit. Each contains Eight #8 x 1-1/2" Philips screws and Eight 8A Tinnerman N. Snaps over edge of panels or into center hole locations. Holds itself in place for blind assembly. "Floats" free for easy alignment. Tinnerman nuts are used to replace threaded nuts, lock washers, and spanner washers; lighter than other types of self-locking aircraft fasteners. Install quicker, easier, and are vibration resistant. Give maximum holding power at minimum cost per fastener. Turned-up ends prevent scoring of surfaces. Alternate: A1348-8Z-1D. Learn More

MS-043 - Hardware, Speed Nut / Retaining Ring.

Also known as flat-style speed nuts, these have a large surface to distribute loads better than standard and flanged external push rings. Use them on unhardened shafts that are softer than the push ring. The ring bites into the metal to form an interference grip. Spring nut provides the correct amount of spring tension without damaging surfaces. Eliminates the need for lockwashers and spanners. For use with threaded screws and studs. Reusable. Nut surface accepts paint without clogging.

Threaded Fasteners for Holding Products/Items Approximately 0.25" in panels (1/4").

IE: Lamps, Miniature Jacks, etc.

Dimensions: 0.625" Long x 0.437" Wide. (5/8" X 7/16")

ID is 0.261" x 0.282".

Propertise: Magnetic,Spring Steel

Package of 50.

Alternate: 90528A12

New Old Stock

 

Learn More

Mill-Max - 3620-2-32-15-00-00-08-0 - Circuit Board Hardware - Terminal Pin, PCB 10u AU OVER NI, Package of 10.

Product Category: Circuit Board Hardware - PCB

Product: Pins    

Type: Terminal Pin, Edge Mount

Length: 0.356 in             

Material: Brass Alloy, Gold Plated           

Brand:  Mill-Max            

Packaging: Bulk

Plating: Gold over Nickel            

RoHS:  Details

Package of 10.

 

Learn More

Unidentified MFG - 43370 - Hardware, Washer. 1" OD.

Rubber washer with 0.25" hole x 0.058" thick.

Material: Rubber.

Note: Feels like silicone rubber.

New Old Stock.

Applications: Electrical or Vibration Isolation / Suppression

Package of 25.

Learn More

Hardware, handle repair kit. B-50-A for B-32-A handle assembly. Learn More

Military - MS51957-22 - Hardware, Screw.

Philips Pan Head

4/40 x 1-1/4" Long.

Package of 25.

Learn More

Hardware. Wire connector, splice. Wire nut. Model 83. Material: plastic. Conductor accommodation type: Screw cap with spiral thread single end. Dimensions: 0.562" D x 1.125" long. ID at opening 0.407". Color: beige. Listed: UL/CSA. Package of 25. Learn More

CENTURY - Art PC Board One Circuit board, blank.

Predrilled.

Dimensions: 2.75" x 1.5" x 0.063" thick.

Package of 50.

Learn More