Encoders

Encoder, rotary. Bidirectional. 10 Pulse/Rev, 5-26V. Mount: 4 holes = 6/32 UNC-2B threads x 0.187 deep, with 50mm centers. Dimensions: approximately 57mm square x 57mm high. Shaft: 3/8" single ended. 5 Pin male MS connector. Complete with manufactures wiring instructions and guidelines. Qube. Learn More

Rotary Optical Encoder. Incremental. Insta-Mount. Enclosed, complete with attached 5 conductor shielded cable, single ended. Dimensions: 2.125" D round x 1.045" high with 2 hole mount 1.812" centers. More info: http://www.beiied.com/PDFs2/MX21.pdf Learn More

Rotary shaft encoder. Includes report of acceptance tests, For S/N 74586. Dimensions: 27mm D x 67mm plus 8.8mm long 3.3mm shaft with 34 teflon leads 37" long. No other data available. S/N 74590. New. Learn More

Potentiometer. Resistance: 5K Ohm (1st) section, 20K Ohm (2nd) section. dissipation: 1 watt. Marked: Rotary actuator travel in angular degrees: 3116. (about 8.65 rotations) CUP-A. Cylindrical servo mount, 6 wire leads. Dimensions: 1.813" (46.0mm) D x 1.993" (50.6mm) high. Single shaft: slotted, 0.125" (3.1mm) D x 0.442" (11.2mm) long (plus 2.0mm seat). Note: Resistor, variable, Wirewound, Precision. Military NSN 5905-00-769-4626. Learn More

240 PPR - Unidirectional with analogue output linear proportional to speed of rotation. 1V / 100 laps - 1V / 1000-RPM - New mating Connector included - 11-25V 30mA 5,000-RPMmax Fmax=50kHz, for output with hysteresis, X4 signal is a sequence of rectangular pulses. Open Collector Output. Custody: Anodized aluminum face plate, plastic housing. Moment of inertia: 50gr cm - Angular accelerattion: 2000 rad/sec2. Learn More

ACCU-CODER INCREMENTAL SHAFT ENCODER60 PULSES PER REVOLUTIONModel 721 - AC Powered Unidirectional EncoderDesigned for use where DC power is unavailable. It is essentially a 711 with a built-in 120 VAC power supply. MATING CONNECTOR INCLUDED

Made in USA - New Old Stock

Learn More

OPTICAL ENCODER 390-Pulses per Revolution 12VDC 3/4"Hollow for 4K RPM Shaft 0-6000Hz 10-oz running torque 2.25"dia x 1.735" thick - NEW sealed ball bearings - 12V@25ma DC - Square wave out Sinks 20 mA - 1uSec rise time Aluminum with black anodized finish, 3-conductor cord 6' long wt:8oz Designed to mount directly on a motor shaft. As the shaft rotates a square wave output pulse is generated that varies at a rate proportional to shaft speed. Ideal for motor speed control or tachometer feedback applications. Just ideal! Learn More

Input: 5/28VDC Has brass coupler with 0.367" ID, short cable w/ 4-pin Male 14S Amphenol panel mount connector. 1.5"OD X 1.4" with coupler and mount. Learn More

Encoders, rotary. Optical. Dimensions: 2-5/16" dia x 1-1/3" high with a 1/4" shaft 9/16" long. Used/RFE/Removed from equipment. Learn More

Encoders, rotary. Optical. Used/RFE/Removed from equipment. Learn More

Rotary Optical Encoder. Incremental. Insta-Mount. Learn More

ENCODER PRODUCTS CO. - 220C OC - 220C-12-600-OC-.750L - Optical Encoder, Hollow Shaft.

Status: Discontinued

ACCU-CODER. 600-pulses per revolution.

ENCODER SHAFT INCREMENTAL 5VDC 180CPR

12VDC 3/4"Hollow for 4K RPM Shaft 0-6000Hz.

10-oz Running torque.

2.25"D x 1.735".

Sealed Ball Bearings.

Supply: 12VDC at 25mA.

Square wave output sinks 20 mA.

1uSec rise time.

Aluminum with black anodized finish, 3-conductor cord 6' long wt: 8oz

New Old Stock - Made in USA

Note: Repais of used Encoders cost as much as $428.

Learn More