Motors
Electric Motors
Electronic Surplus distributes electric AC and DC motors. Depending on the powered needed to operate your equipment, you’ll want to decide which electric motor works best for your needs. For instance, an AC motor replacement is ideal for someone who requires a powerful source of energy for an extended period of time. On the other hand, a DC motor is essential for purposes that can adjust the level of power more regularly.
If you’re unsure which electric motor for sale is right for your needs, contact us. We’d be more than happy to discuss it with you. If you already know what suits your needs, take a look at our selection of surplus motors below.
- JAPAN SERVO - KS7P8-11 - P/N 6813649 - Motor, AC geared. Synchronous 25V 250, 300RPM.Special Price $13.98 Regular Price $18.50READY TO SHIP - ONLY 44 LEFT IN STOCK!
JAPAN SERVO - KS7P8-11 - P/N 6813649 Motor, AC geared.
Synchronous 25V 50/60Hz
Speed: 250/300RPM.
Requires 20uF capacitor (included).
On a 2.78" Square Plate with 4 mounting holes 2.2" apart.
Shaft: 1/4"shaft x 0.6" long and has a gear 0.49" D.
Motor is 1.6" behind plate.
Maybe replaced with p/n 6813649.
Very Old Stock
Made in Japan
Learn More - Honeywell/Microswitch - 33VM82-020-11 - 24VDC Control Motor with TachometerSpecial Price $249.98 Regular Price $350.00
Honeywell/Microswitch - 33VM82-020-11 - 24VDC Control Motor with Tachometer.
5.7Oz-In/Amp Torque Constant.
Rotor Inertia: 60 Oz-In-Sec*Sec 6.6Amps RMS.
Terminal Resistance 85-Ohms.
4"OD x 6.4" Long Including DC Analog Tachometr
Voltage Constant: 2.5V/KRPM.
Terminal Resistance: 50-Ohms.
Voltage Ripple: 1.5% P-P
0.5" Diameter Shaft with 1.6" Diameter rubber wheel.
Proudly Made in USA
Learn More - HAYDON - 36890-60 - 60RPM MOTOR 115VAC GouldSpecial Price $28.98 Regular Price $32.50Out of stock
HAYDON - 36890-60 - 120VAC 60RPM MOTOR for Chart Recorders
1/8"-Shaft 2" X 1.25" X 1.75" GOULD / BRUSH PLASTIC GEARS IN METAL HOUSING
Learn More - Honeywell - 32003440-005 - Three phase enclosed bypass switch.$275.00Three phase 60Hz enclosed variable frequency drive bypass system. Inverter Bypass With Overload Protection. 200/208 = 7 1/2HP / 240V = 10HP / 480V = 20HP / 600V = 20HP OVERLOAD AMP RANGE = 22-27 AMPS - Learn More
- GOULD - M33Y-SNRY-Y004-1B - 24VDC 10hp 195 Lb-In PM SERVO MOTOR=NEW$995.0024V 10HP 195 Lb-In PERM-MAGNET SERVO MOTOR Slightly Used but appears in good condition - Brushless Resolver type Feedback - this motor was probably rated to 3,000 RPM using a 250V 20A drive - Motor Dia is 7-inches x 12" long -Shaft is 1.25"keyed and 2-11/32"long - BACK EMF Ke 70.4V/KRPM - TORQUE CONSTANT Kt 10.3 Lb-In/Amp - 16.2Amp STALL CURRENT - Connection Diagram 497-302-0077 - Outline Dwg 497-206-0097 Learn More
- GEMCO - 1986-1877 - RESOLVER RATIO: 6/1$175.00READY TO SHIP - ONLY 4 LEFT IN STOCK!
RESOLVER IN HEAVY DUTY MOUNT RATIO 6/1 SHAFT: 3/4" KEYED
Learn More - DYNAPAR / DANAHER - 3201001230 - Encoder, rotary. Incremental 100-PPR.$200.00READY TO SHIP - ONLY 1 LEFT IN STOCK!
Encoder, rotary. Incremental 100-PPR. Bidirectional. Power requirements: current sink, TTL, TTL liner driver: 5 - 26VDC at 80mA max. plus load: CMOS line driver: 5 to 15VDC at 80mA max plus load. Output current: open collector: 40mA sink at 0.5V; line driver: 40mA source/sink. Environmentally sealed enclosure. Shaft: 3/8" single ended. 8830 TTL line driver. MS3102E-16S-1P, 7 pin male connector. Note: Qube. Complete with manufactures wiring instructions and guidelines.
Learn More - Chrysler Dodge Plymouth - 3502680-2043 - Switch, Rocker. 4 Position Blower Motor Switch, Automotive.
Mopar - Chrysler Dodge Plymouth - Heater - Blower Motor Switch, Rocker, Automotive.
Actuator: 4 Position (Off is Open, LO=C TO L, MED= C TO M, HI=C TO M + HI).
Connection: (4 Terminal) Male Quick Connect terminals.
Body: Overall 1.316" long x 1.448" wide x 1" behind panel.
Actuator extends to 1.571" above assembly.
Note: Blower Motor Switch.
Mounted on a plate 1.316" long x 1.448" wide.
Vintage - Genuine Chrsyler Dodge Plymouth - Factory New Old Stock
Similar to 3502681 (1970's Vintage)
Alternate Appplications - Hobbyist Motor/Fan Control
Learn More - BEI - MX21-591-1 - Rotary Optical Encoder. Incremental. Insta-Mount.$129.00Rotary Optical Encoder. Incremental. Insta-Mount. Learn More
- AUTOTROL CORP. - PX-300 - Motor, timing. 2-RPM 115VAC Geared motor. Used.Special Price $14.98 Regular Price $28.50Out of stock
AUTOTROL CORP. - PX-300 Motor, timing geared.
Supply: 115V 60Hz 4W.
Speed: Approx 2-RPM counter clockwise, looking at shaft.
Mech: Standard pear shaped gear housing (slightly dirty).
Size: 2.526" x 2.144" Mounting: Holes 1.875" centers.
Shaft: 0.177"D keyed.
Lubrication: Permamently Lubricated
Used/Removed From Equipment
UL, CSA & VDE Recognized
Old Stock - Cases may be a little rusty.
(Price reduced due to corrossion that is not affecting operation)
Made in USA
Learn More - Sensata Industries - AIRPAX - L82101-P2 - Motor, stepper. 12V 118 ohm.
Sensata Industries - AIRPAX - L82101-P2 Motor, Stepper.
12V 118 Ohm
15 deg/step.
6 wires.
Mounting: 1-3/8" hole spacing.
Body: 1"D (25.5mm) x 1/2" (12.6mm) deep, with 35mm mount centers.
Shaft: 1.7mm D x 8.7mm L.
Weight: 1 oz.
New Old Stock
Proudly Made in USA
Learn More - ALLEN BRADLEY - AB - 140-MN-0060 SER B w/ 140-A11 - Adjustable Current 0.4~0.6A MANUAL MOTOR STARTERSpecial Price $41.95 Regular Price $49.00SERIES B 690VAC 0.60A Adjustable 0.4 - 0.6A Current MANUAL MOTOR STARTER AC3 2-push buttons w/ (1) 140-A11 1 N.O & 1 N.C. Auxiliary Switch 8 oz. Learn More
- Cutler-Hammer / Eaton - 10172H- 10172H 334A - Thermal Overload Switch, 115-230 VAC, 30A, NewSpecial Price $92.98 Regular Price $120.00
Cutler-Hammer / Eaton - 10172H- 10172H 334A - Thermal Overload Switch
Status: Discontinued
Pilot Duty Ratings: 115-230 VAC, 30A
Body Approximate Overall Dimensions: 2.2" x 1.95" X 1.0"
New Old Stock - This Item has no Shelf Life
NSN 5925-00-783-5581
Made in USA
Learn More - Eaton - Arrow Hart - 7810-UD - AH7810UD - Motor Controller, Manual Contactor, 3 Phase, 3 Pole 30 A @ 250VAC, 20A @600VACREADY TO SHIP - ONLY 1 LEFT IN STOCK!
Eaton -Arrow Hart - AH7810-UD - Motor Controller, Manual Contactor
Industrial Grade Manual Motor Controllers
Phase: 3 Phase
Poles: 3 Pole
Amperage: 30 Amps
Voltage: 600 VAC
Termination Style: Front Wired Screw
Max. AWG Wire Size: 10 AWG
HP Rating: 7.5@240VAC, 15@480VAC, 15@60VAC
Dimensions: Height 1.7" X Width 3.7" X Diameter 2.6"
Positive-contact design enhances fast-make/slow-break
Silver-alloy contacts for maximum conductivity and service life
Back and side wire terminals accept up to #10 AWG solid copper wire. For stranded #8 AWG wire, remove terminal clamp and use ring terminal
Oversized #10 triple-combination terminal screws are vibration resistant
All molded parts are thermoplastic to resist impacts, chemicals, temperature, tracking and arcing
Insulating barrier between terminals provide isolation from each phase
Nickel-plated brass mounting yoke for superior corrosion resistance
Large toggle provides positive actuation, even with gloved hand.
Note: Arrow Hart P/N 7810-UD changed to AH7810UD following acquisition by Eaton.
High Quality Commercial - New Old Stock.
UL Class: UL508
Proudly Made in USA
Learn More - Bodine Electric - 24A4BEPM - Permanent Magnet DC Motor, 1/7 HP, 2500 RPM, 90/130 VDCSpecial Price $169.98 Regular Price $249.00READY TO SHIP - ONLY 1 LEFT IN STOCK!
Bodine Electric - 24A4BEPM - Permanent Magnet DC Motor, 1/17 HP, 2500 RPM, 90/130 VDC
The Bodine Electric 24A Series Permanent Magnet DC Motors have consistent performance, long life, and reliability. Since 1905 Bodine motors, gearmotors, and controls have been used in assembly equipment, conveyers, packaging equipment, copiers, lab instruments, photographic processors, medical and other scientific apparatus; wherever component size, weight, reliability and integrity are prime considerations.
Model Number: 0049 Totally Enclosed PM Motor
Category: 24A Series Permanent Magnet: DC Motor
Speed: 2500 RPM
Rated Voltage: 90/130 VDC
Amps: 0.69/2.50
Motor HP: 1/17
Length XH: 4.68 inch
Weight: 3.4 lbs.
Product Type: 24A4BEPM
Connection Diagram: 074 10101
Made in USA
Note: New As Removed from New Machine
Learn More - Bodine Electric - 24A4BEPM - Permanent Magnet DC Motor, 1/17 HP, 2500 RPM, 90/130 VDCSpecial Price $189.98 Regular Price $249.00Out of stock
Bodine Electric - 24A4BEPM - Permanent Magnet DC Motor, 1/17 HP, 2500 RPM, 90/130 VDC
The Bodine Electric 24A Series Permanent Magnet DC Motors have consistent performance, long life, and reliability. Since 1905 Bodine motors, gearmotors, and controls have been used in assembly equipment, conveyers, packaging equipment, copiers, lab instruments, photographic processors, medical and other scientific apparatus; wherever component size, weight, reliability and integrity are prime considerations.
Model Number: 0049 Totally Enclosed PM Motor
Category: 24A Series Permanent Magnet: DC Motor
Speed: 2500 RPM
Rated Voltage: 90/130 VDC
Amps: 0.69/2.50
Motor HP: 1/17
Length XH: 4.68 inch
Weight: 3.4 lbs.
Product Type: 24A4BEPM
Connection Diagram: 074 10101
Made in USA
Learn More - YASKAWA Electric Mfg - 616G3 - VARISPEED 3 PHASE AC DRIVE GPD616G3$175.00Out of stockVARISPEED 616G3 3 PHASE AC DRIVE. OUT: 0-460V 1 HP 0-400Hz 2.2kVA 2.9Amps IN: 380-460V 50/60Hz - Includes DigitalOperator JVOP-100 NEMA 1 ENCLOSURE, TORQUE EXCEEDING 150% UNDER OPERATION AT 1Hz. 400V CLASS INVERTER. CIMR-G3E40P7 INPUT: 3 PHASE AC 380~460V 50/60Hz @ 3.2A or 510-620VDC @ 3.9A OUTPUT: 3 PHASE AC 0~460V 2.2kVA @ 2.9A 0-400Hz INCLUDES: DIGITAL OPERATOR(PN#JVOP-100) WITH 5 DIGIT DIGITAL DISPLAY - STATUS INDICATING LIGHTS - MULTIPLE KEYPAD OPTIONS---JOG - FWD/REV - RUN - STOP - RESET - DIRECTIONAL AND PROGRAM/DRIVE. Learn More
- YASKAWA Electric Mfg - CIMR-V7AM40P2 - 380~460VAC DRIVE 0.2kW 0-400Hz 1.2A$195.00YASKAWA AC DRIVE 315/V7 0.2kWUSED - Input 3-Phase 380-460 VAC, Output: 3-Phase 0-460V 0-400Hz 1.2 Ampfront panel control, 4-digit display weighs 1.2kg Learn More
- WARNER & SWASEY - 5309-1011 Type 2CW - Optical Encoder 2000-PpR$195.00Optical Encoder Input-2000PPR Range:400,0006-1/8 " high x 5-1/4" dia. With one 32-Pin (M) panel mt military circular connector 3/8" dia shaft 1-1/8" long (Keyed) RFE-USED Make Us An Offer!!!! Learn More
- Unidentified MFG - 9-154 - Motor, AC. 115VAC Open C-Frame Fan Motor.Special Price $12.98 Regular Price $18.50READY TO SHIP - ONLY 24 LEFT IN STOCK!
Motor, 115VAC, Open C-Frame Fan motor.
Shaded Pole direct drive fan motor.
Sleeve Bearings.
Continuous duty.
Mounting: 2 studs
Shaft Diameter 3/16" (.1875")
Shaft Length 1.45" D Shape
Laminations 2.4" Square
3 Wire, 2 Speed.
Note: C-Frame motors are mechanically reversible by removing the 2 screws holding the bearing housings together
Learn More
and reversing the rotor/shaft assembly. Studs can also be reversed to the other side. - Unidentified MFG - 30701 - Motor, DC. 1-3VDC. Hi Torque.Out of stock
30701 High torque DC motor.
This compact DC Motor would be great for a variety of projects and experimental uses. It requires only 1VDC to operate and provides optimum performance at 3VDC.
1-3VDC, 15,500-RPM, approximately 1 Amp.
Dual shaft 2.3mm 15mm long.
Reversible PM.
Dimensions: 27.5mm/1.08" OD x 1.47" long excluding shafts.
Relatively high torque.
Learn More - SUPERIOR ELECTRIC CO. - SS250-1002 - Motor, Slo-Syn stepper 9VDC 1.5A 225-Oz-In.$75.00Motor, Slo-Syn stepper. Supply: 9VDC. N/P Current: 1.53A . Steps: 200 steps/revolution. Torque: 225 Oz-In. Direction: reversible. Wire count: 6. Mech. Mtg: 3-hole mounted to 4-hole plate. Shaft: has a removable pulley attached. Weight: 8 lbs. Learn More
- SUPERIOR ELECTRIC CO. - M063-CS09E - Motor, stepper. 2.25VDC 4.6A 1.8 Deg.$88.00Out of stockMotor, stepper. Synchronous - 2.25VDC 4.6Amp 200 Steps/Rev, 1.8 Degree 150 oz in. Dimensions: 57mm D x 101 mm long. Dual Shaft : 6.6mm x 18mm long. Square flange with 4 holes 47mm centers, 7 pin connector. Class A insulation. May have shelf wear. Learn More
- SUPERIOR ELECTRIC CO. - SS50-1292U - Slo-Syn Synchronous Stepping Motor, 120V/60/0.5Amp. 6 RPMSpecial Price $86.98 Regular Price $165.95READY TO SHIP - ONLY 2 LEFT IN STOCK!
SUPERIOR ELECTRIC CO. - SS50-1292U - Motors, AC Geared.
Xerox 127P1365
Voltage/ Current Input: 20V/60/0.5Amp.
Sppeed: 6RPM.
Requires capacitor for start or run.
Heavy Duty, 3 wire.
Motor is 3.35" DIameter
Impedance Protected
Assembly is 5" tall x 7-1/2" long x 5-1/2" wide with 4 mounting slots.
Output is 1.15"[30mm] D on a 3/8" Flatted Shaft.
Note: Reversible Slo-Syn.
Requires a 250 Ohm 25 watt resistor and an 8uF 230VAC capacitor.
Used / Removed from Equipment
Made in USA
Learn More