Mounting Hardware
- BIRD - 5-1357-3 - Connector, Electronics Solder Eyelet, Rivet/Eyelet/Terminal. Package of 100.
BIRD - 5-1357-3 Connector, Electronic Solder Eyelet, Rivet/Eyelet/Terminal.
Electronic eyelets are flanged tubular metal conductors inserted into a printed circuit board. They make electrical continuity between the circuitry on both sides of the board, and are an attachment point for soldering component leads.
Type: Solder.
Appears to be Silver Plated Brass (High thermal and electrical conductivity)
Metric Dimensions: Outside lip is 6.1mm OD, 2.9mm ID with a shaft 3.5mm round and 6.7mm tall under Lip.
Inch Dimensions: Outside lip is 0.240" OD, 0.114" ID with a shaft 0.138" round and 0.264" tall under Lip.
Applications: Secure High Current Electrical and Ground Connections or repairs to chassis and PWBs.
Chose the proper eyelet keeping the following in mind:
LUF The length of the eyelet barrel under the flange should be 0.020-0.035”/0.630-0.890mm greater than the thickness of PCB(this allows the for the right length after the flange is formed)
ID Eyelet inside diameter should be 0.003-0.020”/0.075-0.500mm greater than the component lead diameter for proper fit of the eyelet through-hole component lead.
FD The flange diameter should be sized so that it does not protrude out onto other pads or conductors in the vicinity
OD The clearance in the PCB hole should allow the eyelet to be inserted without undue force but, but should not exceed 0.125mm greater than the eyelet outside diameter.Additional Information: http://www.intl-eyelets.com/short_course_on_electronic_eyelets.htm
Genuine Vintage Bird Electronics Hardware - New Old Stock
Package of 100.
Learn More - ROBINSON AVIATION - K166-8D - Hardware, Shock Vibration Isolation Spring Mount. 0.19" ID Hole.IN STOCK - MORE THAN 100 READY TO SHIP!
ROBINSON AVIATION - K166-8D Hardware, Shock Vibration Isolation Spring Mount, Metallic Dampener.
Anti-Vibration Compression Spring Mount
0.19" ID Hole.
Spring Supported
Flange-Mount on 1.385" Centers.
Mounting Hole Diameter: 0.138
Learn More - EDWARDS SIGNALING PRODUCTS - 349 - Weatherproof Cast Mounting Box.Special Price $24.98 Regular Price $32.50
EDWARDS SIGNALING PRODUCTS - 349 Hardware, Enclosure.
The 349 is a weatherproof Mounting Box is perfect for mounting a variety of Edwards signaling appliances such as bells, horns and sirens. It is made from die-cast aluminum and finished at the factory with a baked sage gray enamel finish.
- Rugged Die-Cast aluminum
- Tapped for 3/4" (19 mm) conduit
- Molded neoprene gasket
- Corrosion resistant finish.
Back Mounting Box.
Construction: Rugged Die-Cast Aluminum
For Edwards Signaling 340 6" or 10" Adaptahorns.
Color: Gray.
Size 6-1/2 Inch Diameter X 1-5/8 Inch Width
Applications: Fits 6”, & 10” 340, 435, 439D, 5520 Series Bells, Duotronic horn/siren
UL Listed for outdoor use.
More info: http://www.edwards-signals.com/index.cfm?pid=185
UPC: 782640242001
Alternate: Newark 92F6379
Learn More - Brady - PT-409 - Hardware, Ribbon Cable Clamp/Clip. Self Adhesive Backing. Supports up to 1 Inch Wide Ribbon Cable.$0.29 As low as $0.12Out of stock
Brady - PT-409 - Hardware, Flat Ribbon Cable Clamp/Clip.
Made from extruded PVC, these small, flat cable clamps are just the thing for clipping and holding flat cable in semi-permanent position. An adhesive-backed foam mounting pad holds the clip securely in position.
Self-Adhesive Backing eliminates need for tools when monting clip.
Low profile clip for single or multiple layers of flat cable.
For up to 1 inch (25.4 mm) wide ribbon cable.
Low profile clip for single or multiple layers of flat ribbon cable
Mount: Easy-to-install.
Material: Polyvinyl Chloride
Color: Gray PVC.
Operating temperature: -40 C to 85 C
Dimensions: 24mm x 25mm x 9.3mm
Function: Routing
Alternates: Thomas & Betts FRPV-1000-8-C, RS pro 233-190, Panduit FCC-A-D8, 3M 3484-1000, ABB FRPV-1000-8-D, FIX-FCC-25.
Learn More - Rittal Corp - 9581-000 - Large Hinges with Fixing Material. For Enclosure PK 9514-000 & PK 9524-000.
Rittal Corp - 9581 000 - Large Hinges with Fixing Material. For Enclosure PK 9514-000 & PK 9524-000.
Hinges: For hinged attachment of lids. The supplied drilling template ensures problem-free assembly.
1 set = 2 hinges, 4 assembly screws, 3 polyethylene sealing bungs, 1 drilling template.
Color: Grey - RAL 7035
Material: Polystyrene
Operating Temperature: 80 C
Approvals: CUL, EN
Made in Germany
- CBO - 7-229 - Hardware, Insulator/Stand-Off. Porcelain High Voltage & High Current, Heavy Duty.
CBO - Hardware, Insulator/Stand-Offs. Heavy Duty.
Material: Brass and Ceramic.
Base mount: Oval with 2-1/4" centers (1-5/8" x 2-7/8").
Dimensions: 4" Tall.
Porcelain Insulator: 1.25" Diameter
Brass Support: 1.625" Diameter
Weight: 1.1 lb.
Applications: High Power Transmitters
Alternate/Similar: Lapp 14760 & 24114
Proudly Made in USA
Learn More - Signal Measurement Co. - 106TSP - Adjustable Universal Pedestal Equipment Mount 4" to 8"
Signal Measurement Co. - 106TSP - Adjustable Universal Pedestal Equipment Mount 4" to 8"
This Pedestal Mount can angle, tilt, swivel and extend your holder/device for a better viewing position. This mount swivels 360 degrees horizontally and vertically. It extends 4 to 8 inches (100 - 200 mm) and can be attached to any flat surface. The face plate has an AMPS hole pattern to accommodate most holders, cradles, mounts and car kits.
Features:
- Strong Durable Construction
- 360 Degree Swivel
- Provides a firm installation
- Up to 8“ high with 2” extension.
- Aluminum 0.500" Diameter Extension rod.
- Outer Support Sleeve 1 inch diameter with 0.50” inner rod.
- Allen Wrench with 3 additional set screws.
- Compatible with any holder using the standard 4 Hole "AMPS" pattern.
Specifications:
- Material: High Grade Aluminum Rods, Steel Base Plates, Plastic Sleeves
- 2.50 Inch Diameter Round Mounting Base
- Wingnuts for easy adjustment
- 1/8” Think Steel Face Plate
- Color: Black
Applications: Use in the Car, Home, Boat, Camping, Work bench to Mount Cell Phones, Tablets, Test Equipment, Cameras, Speakers, GPS, Radar Detector, Fish Finders, Gaming, Rear View LCD Monitors, Displays.
Learn More - UMPCO - 1919WDG11 - Cushioned loop clamp, 0.688" OD.Special Price $1.49 Regular Price $2.00
UMPCO - 1919WDG11 Hardware, cable clamps.
Cushioned loop clamp, 0.688" OD.
Inside loop ID: 0.673 - 0.703" max.
Tongue hole type, oil resistant.
Distance from loop center to tongue end: 1.032".
Center to center distance between loop and mounting hole: 0.799" min to 0.829' maximum.
Overall width: 0.490".
Material: steel, carbon with synthetic rubber mil grade Mil-R-3065.
Material thickness: 0.050".
Military NSN 5340-00-664-8163.
More info: http://www.umpco.com/products_pdf/AS21919.pdf
Learn More - UMPCO - 5340-00-922-6300 - Cushioned Loop Clamp, 1" ID.Special Price $1.98 Regular Price $3.00Out of stock
UMPCO - 5340-00-922-6300 Hardware, cable clamps.
Cushioned loop clamp, 1" ID.
Tongue hole type, oil resistant.
Distance from loop center to tongue end: 1.125".
Center to center distance between loop and mounting hole: 0.906".
Overall width: 0.625'.
Material: steel, carbon with synthetic rubber mil grade Mil-R-3065.
Material thickness: 0.032".
Double marked MS21333-77.
Military NSN 5340-00-922-6300.
More info: http://www.umpco.com/products_pdf/NASM21333.pdf
- UMPCO - 5340-00-050-2740 - MS21333-75 -Cushioned loop clamp, 3/4" ID.Special Price $1.69 Regular Price $2.50
UMPCO - 5340-00-050-2740 Hardware, cable clamps.
Cushioned loop clamp, 3/4" ID. Tongue hole type, oil resistant.
Distance from loop center to tongue end: 1.0".
Center to center distance between loop and mounting hole: 0.781". Overall width: 0.500:
Material: steel, carbon with synthetic rubber mil grade Mil-R-3065.
Material thickness: 0.032".
Double marked MS21333-75.
Military NSN 5340-00-050-2740.
More info: www.umpco.com/products_pdf/NASM21333.pdf
Learn More - ALLEN BRADLEY - AB - 871C-N3 - AB - 871C-N3-SER A - Switch, Proximity. 18mm Hex Nuts. Package of 2.
ALLEN BRADLEY - AB - 871C-N3 - AB - 871C-N3 SER A- Switch, Proximity Nickel Plated Brass Nuts. Package of 2
Genuine Rockwell Automation Parts
Large Hex Nuts 18mm
Nickel Plated Brass Mounting Nut
UPC: 662073675471
Proudly Made in USA
Package of 2
Alternates: GXM3MD2439, 871T-N4, ST02, OP-3052
Learn More - MATSUSHITA - HG2-SF - HG Relay Socket 20Amp 250VSpecial Price $5.98 Regular Price $7.98
MATSUSHITA - HG2-SF New Relay sockets for HG relays
20Amp 250V
Power relay socket
PCB MT 8-pin
Lead free.
New Old Stock
Learn More - Umpco - MS-921333-71 - 5340-00-057-2904 - Hardware, Cable Clamp. 1/2" - 13/64".$0.98 As low as $0.49
Umpco - MS-921333-71 - 5340-00-057-2904 -Hardware, Cable Clamp. 1/2" - 13/64".
Cushioned Metal, Synthetic Rubber Jacketed.
Mount: 5.0mm hole.Diameter: 0.203"
Material Thickness: 0.032"
Center to Center Distance Between Loop and Mounting Hole: 0.656 inches nominal
Distance from Loop Center to Tongue End: 0.875 inches nominal
Loop Inside Diameter: 0.500 inches nominal
Note: Clamp is actually marked MS21333.
Military bags are double marked 5340-00-057-2904.
Applications: Commerical, Industrial, Engine Wiring Harness
- General Electric - CR2940U301A - Switch, Pushbutton. Contact Block Only, Mounting Plate.$10.00Out of stock
General Electric - CR2940U301A - Switch, Pushbutton.
Contact Block Only, Mounting Plate.
Oil Tight.
1NC
Voltage: 600VAC Max.
Front mount.
Learn More