Stepper Motors

Motor, stepper. 6VDC 1.2Amp 1.8 Degree/Step 2PH. Vexta. Mount: Panel. Flange 2.225" square with four holes at 2.575" centers (each 1.86" each spacing). Dimensions overall 2.236" D round x 2.204" high, plus 1/4" D shaft 0.74" long. Note: Shaft has one side flattened. 6 Wire. Weight: 1.14 lbs. Learn More

12VDC 4.25W 6-lead Bifilar 15-degree Stepper Model #ABS Part #3007-001 Reduction: DD - Volts: 12DC Step Angle: 15-degrees. Mounts with two holes on 2.38" centers, pear shaped gear cup Instrument Motor 0.125" shaft half an inch long. Some instructions supplied. Learn More

42mm dia x 14.5mm thick, 2.9mm shaft 11mmL with 6.2mm 10-tooth brass Gear 4-hole plate, 35mm centers Stepper Motor 4-Wires, 19"long very thin 3.6oz Learn More

6VDC 1.25Amp 1.8degree 4-Phase 6-teflon 15"wires Stepper Motor 2.25"D x 3.0"L 4-hole mounting 1.85" spacing 0.25"D shaft 0.75"L New, Old Stock weighs 2-pounds Learn More

ARC SYSTEMS - 2015-02 - 204239 - Arcustep 24VDC

Step Angle 15 Deg

4 Wire Stepper 

Smoth Ball Bearing Shaft Support

Servo-Mount 50.7mm Diameter x 75mm Long

Plus 11.1mm Diameter Worm Gear 111mm Long - 6.7mm diameter shaft 9.3mm Long at rear.

Four Wire Teflon Leads.

Measured Resistance is either 20 or 40-Ohms fron one wire to any other wire

New Old Stock

Made in USA

Learn More

Motor, stepper. Dual shaft, 8 Wire. Max phase current: Series 1.70Amp Parallel 3.40Amp. Mount: Panel, 47mm centers. Body: 56mm D x 141mm long. Shaft(s) 6.4mm D x 19mm long. Weight: 2.9 lbs. Learn More

Stepper, 18 Deg/Step, 1.5 in-oz, 4 wires, Mounting 2 holes 42mm apart, Body 37x50x20mm thick, Shaft 2x8mm with4.6mm gear,2.6 oz, 4.6mm 10-toothGear. Learn More

Japan Servo Motors - KH42HM2-852 - 1.8 Degree 2 Phase Hybrid Stepping Motor

Commerical Quality KH42 Series 800 Type High efficiency, High Torque, Low Vibration and Low Noise Motor. 

This new series 800 type, which maintains the high torque performance of our conventional 500 Type and lower vibration and noise. High efficiency and high torque have been achieved through our intensive research on magnetic circuitry. A unique  tooth profile has been employed through the development of a new  proven theory to achieve low vibration and low noise. 

Specifications 

NEMA 17

Drive Method - Uni-Polar 6 Wire

Bearing Description

Step Angle - 1.8 Degrees/step

Voltage - 24 Volts 

Current - 0.38 Amps/Phase

Winding Resistance - 22.4 Ohms/Phase

Inductance - 21.5 mH/Phase

Holding Torque - 2.0 kgf cm (28 ounce inch)

Detent Torque - 150 gf cm (2.1 ounce inches)

Rotor Inertia - 42 g cm2 (0.23 ounce inches)

Weight -  260 g (0.57 Lbs.) 

Insulation Class JIS Class E (120 C 248F) UL Value Class B-130C 266F)

Insulation resistance  500 VDC 100Mohm min.

Dielectric Strength - 500 VAC 50 Hz 1 minute

Operating Temperature Range 0 - 50C

Allowable Temperature Rise 70 degrees

Dimensions 1.65" X 1.65"  X  1.34" (42mm X 42mm X 34 mm Max) 

Superior in Quality, Reliability, and Durability to the Cheap Chinese copies.

NEMA 17

Drive Method - Uni-Polar 6 Wire

Bearing Description

Step Angle - 1.8 Degrees/step

Voltage - 24 Volts 

Current - 0.38 Amps/Phase

Winding resistance - 22.4 Ohms/Phase

Inductance - 21.5 mH/Phase

Holding Torque - 2.0 kgf cm (28 ounce inch)

Detent Torque - 150 gf cm (2.1 ounce inches)

Rotor Inertia - 42 g cm2 (0.23 ounce inches)

Weight -  260 g (0.57 Lbs.) 

Insulation Class JIS Class E (120 C 248F) UL Value Class B-130C 266F)

Insulation resistance  500 VDC 100Mohm min.

Dielectric Strength - 500 VAC 50 Hz 1 minute

Operating Temperature Range 0 - 50C

Allowable Temperature Rise 70 degrees

Dimensions 1.65" X 1.65"  X  1.34" (42mm X 42mm X 34 mm Max) 

Superior in Quality, Reliability, and Durability to the Cheap Chinese copies.

ApplicatIons: RobotIcs,  3D Printer,  Arduino,  CNC,  Router.

 

 

Learn More

Motor, Slo-Syn Stepper, Bipolar. Supply: 3.5VDC. N/P Current: 5.0A. Winding Res.: 0.7-ohms 9.2mHy. Steps: 200 steps/Rev. Torque: 760 Oz-In. Direction: Reversible. Wire count: 4 terminals. Mech. Mtg.: NEMA 42. Body Dimensions: 110mm frame. Ratings are for series connections. Used. Learn More

Motor, Slo-Syn Stepper with Encoder. Supply: 3.21VDC. N/P Current: 5.1A. Steps: 200 steps/Rev. 3-Stack. Winding Res.: 0.629-ohms 8.31mHy. Torque: 1155 Oz-In [816Ncm]. Motor Wire count: 4 wire leads. Encoder wire count: 8-wires. Body Dimensions: 85mm/3.53"square x 6.25"L. NEMA 34. Shaft: 0.50"D flatted shaft 1.1"L. 9 lbs. Used as demonstration model only, no marks on mounting face plate. Learn More

Motor, stepper. Slo-Syn. Supply: 3.48VDC. N/P current: 3.25A. Winding res.: 1.07-ohms, 11.2mHy. Torque: 770-Oz-In [554Ncm]. Wire count: 4 wire leads. Weight: 7 lbs. Used. Learn More

Motor, Slo-Syn Stepper, Bipolar. Supply: 2.6VDC. N/P Current: 4.0A. Winding Res.: 0.65-ohms 14.6mHy. Steps: 200 steps/Rev. Torque: 2000 / 1200-Oz-In. Direction: Reversible. Wire count: 4 terminals. Mech. Mtg.: NEMA 66. Body Dimensions: 165mm frame. SPEC.A213803. Ratings are for bipolar connections. Learn More

Motors, stepper. SloSyn synchronous 3.47VDC, 2Amp, 200S/R. Hold: 325 oz in. Attached encoder 220022/219273, 500PPR with a DB9 female connector.Motor case: mount 3-1/4" square with 3-3/4" mt ctrs x 4-5/8" long body. Shaft: 0.380" D x 1-1/8" long. Connections: 4 conductor foil shieled cable plus ground wire. Learn More

Motors, stepper. 4.2V, 1.9Amp, 200S/R, Hold: 100 oz in. 64Deg rise. NEMA 23, 2-stack. Case: 2-3/16" square mount with 2-1/2" ctrs. 1/4" shaft x 3/4" long.Connections; 8 pin male header with mating female socket included. Learn More

SHINANO KENSHI - STH-39D249 - 6 Wire Stepper Motor.

Status: Discontinued

Dimensions: 39mm Square x 37mmD.

NEMA Size 14

4.7mm Flatted Shaft 24mmL.

1.8 Degree per Step

7.1-Ohm Coils

6-long Wires.

New

Made in Japan

Learn More

STEPPER MOTORS REV 5V 1AMP 0-150PPS REV 0-375 RPM 8-wire mounted on L-shaped bracket 4.235 x 3 x 2"D double flats on 6.7mm 1/4" shaft12mm long 70mm dia x 43mm deep 2-poundsRemoved from equip. Learn More

FUJI ELECTRIC - SM35-2006B Motor, stepper.

Supply: 13VDC.

Coil Resistance: 38 ohm.

Direction: Reversible.

Wire Count: 4-Wire.

Mech. Mtg: Slotted Flange with two slots 42mm spacing

Body Dimensions: 35mm dia x 21mm deep.

Shaft: 1.9mmD 7.5mmL.

Note: Fuji Electrochemical Co - Japan.

Learn More

Motor, stepper. Slo-Syn 120VAC 0.1Amp 1000RPM 2.0 OZ In. Dimensions: 2.224" square base with 2.5" mount centers. Used/Removed from equipment. Learn More

Motor, stepper. Slo-syn synchronous 5V 1Amp, 200 S/R = 1.8-degree, 35 oz in. Four (4) hole-mounting, about 46.4mm [1.84"] on 56.6mm [2.23"] plate. Shaft: 0.25", 0.75mm long. Dimensions: 56.7mm D x 52.2mm deep (2.3" D x 2"). Learn More

PACIFIC SCIENTIFIC - E33NLEC-LNF-NS-01 Motors, Stepper. NEMA 34

Status: Discontinued

Bipolar series 65VDC 5.5Amp 202W 1500RPM

1.8DEG/STEP.

Power: 202W.

Dimensions: 86mm D x 155mm deep, 9.6 x 30mm flatted inside thread shaft.

Mounting 70mm centers on 86mm square flange.

Weight: 8.3 lbs.

Additional Information: https://www.artisantg.com/info/Pacific_Scientific_Step_Motors_Datasheet.pdf

Proudly Made in USA

New old Stock

Learn More

Stepper motor. 5.4V 1.5Amp 1.8 Deg/Step. PP6. 6 Wire. Mount: Panel/Flange: 2.220" (56.4mm) square. 4 Hole mount with 2/5/8" centers. Dimensions: 2.224" (56.4mm) D x 3.046" (77.3mm) long, plus shaft. Shaft: 1/4" x 0.75" long. Learn More

Motor, stepper. 12VDC 3 watt. Six (6) wire with gear reduction of 20:1

Learn More

Stepper motor. 2 Phase 1.4VDC 1.9Amp 1.8 Deg/Step. With pulley on 1/4" shaft 20mm long (57.3mm D x 52.2mm tall with pulley overall is 71.6mm tall). Oval mount 66.5mm centers. Motor has 4-Conductor 12" wire leads. Eastern Air Devices. Weight: 1.2-pounds. Learn More

Eastern Air Devices - LA23ECS-36 - Stepper Motor

1.9VDC 2 Phase 3Amp 1.8 DEG.

Stepper Motors 4-Wire

Dimensions: 57mm Dia x 52mm deep plus additional 6.3mm [1/4"] Shaft 18mmL.

Nema 23

IP40

Weight 18oz.

Motor has a 7" long 4-Cond wire and connector.

Square Mount 47mm Ctrs.

Genuine Eastern Air Devices - New Old Stock

Made in USA

Learn More