Other Resistors

INTERNATIONAL RESISTIVE CO INC - LOB-5 0.08< 1% LT - Current Sense Resistor, Metal.

Resistance: 0.08 Ohm

Power: 5W.

Package of 5.

CADDOCK - 1776-24 - Resistor.

The exceptional performance of this extensive family of Type 1776 Precision Decade Resistor Voltage Dividers has been achieved through the special combination of advantages provided by Caddock's Tetrinox® resistance fi lms. This advanced film resistor technology provides the performance characteristics required by the precision input signal circuits of both bench-type and laboratory digital instruments.

Precision Decade Resistor Voltage Divider.

Voltage Rating: 1200V

Resistance Values: 9Meg - 900K - 90K - 9K - 1K Ohms.

Tolerance: 0.25%.

Temperature: -40 C to 85 C

Package: Ceramic 6 Pin SIP.

New Old Stock

Leads may have a bit of residual foam packing that deteriorated and was removed.

CADDOCK - 1776-C541 Resistor.

The exceptional performance of this extensive family of Type 1776 Precision Decade Resistor Voltage Dividers has been achieved through the special combination of advantages provided by Caddock's Tetrinox® resistance films. This advanced film resistor technology provides the performance characteristics required by the precision input signal circuits of both bench-type and laboratory digital instruments.

Caddock's Decade Voltage Dividers offer small size, low cost and are commonly used in high-accuracy, precision analog metering designs. 

Precision Decade Voltage Divider.

Resistance tolerance +/- 0.1%

Voltage: 750V.

Temperature coefficient 25 ppm/C

Resistance values: 900K Ohm, 90K Ohm, 9K Ohm, 1K Ohm.

Package: 5 Pin SIP

RoHS Compliant

Alternate P/N 21J7886

CADDOCK - MP821-0.050R Resistor, Power Film.

Resistance: 0.050 Ohm.

Power: 20 watt @ 25 Deg C if Heatsinked.

Tolerance: 1%.

Maximum Voltage: 300V.

Temp coef: TO-220-2,

Micronox Film Bonded to Copper.

Note: Kool-Tab, Non-inductive.

Excellent transparency for tweeter networks.

Caddock Electronics Inc - MS220

1.5MEG 2W 1% 1KV

Power Film Reistor

Gold Leads

Caddock Electronics Inc, - MP930-2K - Resistor, Power Film.

Resistance: 2K Ohm.

Power: Up to 30 watts at 25 Deg C.

Tolerance: 1%.

Kool-pak.

Package: TO-220-2.

Caddock Electronics Inc, - MP925-5K - Resistor, Power Film.

Resistance: 5K Ohm.

Power: Up to 30 watts at 25 Deg C.

Tolerance: 5%.

Kool-pak.

Package: TO-220-2.

Caddock Electronics Inc, - MP930-0.025R - Resistor, Power Film.

Resistance: 0.025 Ohm.

Power: Up to 30 watts at 25 Deg C.

Tolerance: 5%.

Kool-pak.

Package: TO-220-2.

Caddock Electronics Inc, - MP930-0.050R - Resistor, Power film.

Resistance: 0.050 Ohm.

Power: Up to 30 watts at 25 Deg C.

Tolerance: 1%.

Kool-pak.

Package: TO-220-2.

CLAROSTAT - VR-007 - Rheostat. 10 Ohm. Vintage Radio Tube Filament Control, New Old Stock.

Used in series with tube filaments to adjust current. Extends the "useful" life of RF tubes to keep the emission of the tube above the recommended minimum for the maximum amount of time.

Resistance: 10 Ohm.

Technology: Wirewound.

Mount: Panel.

Threaded Bushing: 3/8" D x 11.3mm long,

Shaft: 1/4" D x 2.5mm high. Screw Driver Adjustable.

Contacts: 2 Solder Hooks.

Marked 140-6607, X-4094-C.

Alternates/Similar: Carter Radio Co. / Central Radio Laboratories Pot Control Wire Wound Rheostats

Genuine Vintage Clarostat - New Old Stock 

Made in USA

10-OHM

Dale - CPR-15-20 - Resistor, ceramic.

Resistance: 2.7 Ohm.

Power: 15 watt.

Tolerance: 10%.

Material: sandstone.

Mount: horizontal.

Dimensions: 1.881" long x 0.498" wide x 0.515" high. New.

Note: Cross RCA P/N: 190487.

FILNOR INC. - 9857-FH80 1.03-Ohm - Grid Resistor, 80 Amp, Class 9857.

Number of Taps: 10

Drawing Number: R27189

Class 9857 - Stainless Steel Grid Resistors
• Standard grid resistors in stock to reduce costly down time
• All units are insulated for 1000 volts AC or DC
• Reliable stainless steel resistor elements and terminals
• Standard 26.5” dimensions for quick replacement of otherbrands
• Stable resistance over wide temperature ranges
• High wattage saves space, weight and cost

Silicon Bonded Mica Insulating Washers -Higher Temperature rating than epoxy bonded.

End Frame Insulator -Molded fiberglass material is used to insulate the connection
between the support rods and the end frame. This allows for the grid structure to be held securely together and double insulated to ground.

Support Rods - Threaded support rods are insulated with silicon bonded mica tubing to provide primary protection from grounding/shorting out.

End Frames - Filnor endframes are designed so that the resistors can be mounted in racks or stacked.

Dynamic Braking Stainless Steel Grid Resistor - stamped grid, chomium alloy stainless steel grid resistors - Reliable stainless steel resistor elements and terminals - 8 evenly spaced taps.

Dimensions: 26.5" X 12" X 6".

Applications: • Crane Control • Dynamic Braking • Neutral Grounding • Harmonic Filters • Mining Equipment • Transit • Load Banks • AC and DC Motor Acceleration

Made in USA

INTERNATIONAL RESISTIVE IRC - GS-3T015R0F - Thick Film Semi-Precision Metal Film

Resistance: 15 Ohm.

Power: 3 watt.

Tolerance: 1%.

Package: Axial Leads, Molded

Effective carbon composition replacement.

Package of 10

KEVLIN - 5089-P - Current Sensor Resistor. 0.01-Ohm.

Current sense resistors are often referred to as 'shunt' resistors. Shunt resistors are used to monitor the amount of current that is flowing through a circuit. Such resistors have very low resistance values, typically less than 50 milli-ohms (0.050 ohms) and often lower.

A 'Kelvin' configuration resistor features four leads or terminations. These four terminal resistors enable current to be applied through two opposite leads and a sensing voltage to be measured across the other two leads. The Kelvin configuration effectively eliminates the resistance and temperature coefficient of the leads. The Kelvin connection can also simplify board design by incorporating all terminals for the sensing circuit into one part. A Kelvin connection is essential for accurate current sensing and simplified board design.

Tolerance: 1%.

Current Sensing Resistors.

Metal Enclosure

Connections: 4 Terminal Leads, 2 Axial Leads Each End.

Dimensions: 2.25" x 1.25", 

Applications: 

• General Use - Power supplies, disk drives, battery power management, control of current detection or over-current detection, motor start, high voltage and precision applications.
• Consumer Goods - Power tools, thermostats, appliances, televisions, smoke detectors, and video cassette recorders.
• Automotive - Anti-lock brake systems, keyless entry systems, air bags, power steering control systems, voltage regulators, powertrain, information centers as well as engine controls and modules.
• Telecom - Telephones, cell phones, pagers, mobile radios, hand-held devices and laptops.
• Medical and Instrumentation - Monitoring systems, pressure sensors, implant products, electronic scales, and a variety of diagnostic equipment.
• Military and Aerospace - Satellites, missiles, surveillance equipment, sonar, and avionic products.

Post Glover Resistors Inc - H10PG - Stainless Steel Gird Resistor, 0.800 Ohm 63A.

Low temperature coefficient stainless steel elements and stainless steel terminals for long-lasting reliability. Positive grid-to-grid connections, with no current carrying washers or spacers which can cause failure. Tig welded connections to eliminate damaging hot spots. PG Steel Grid Resistor.

Resistance:  0.800 Ohm

Current Rating: 63A.

Features
• Stainless-Steel Terminals
• Double Insulated, rated 1500V
• Interchange with all major brands

The Stainless Steel Ribbon Resistors feature a 4-inch-wide stainless steel element that is a serpentine formed from one continuous strip up to thirty feet long. A special Type-406 alloy is used to limit the increase in resistance to only 6% at rated current (375°C rise).

Heavy 304 stainless terminal plates are both mechanically clamped and TIG welded to the element and feature a 2-hole NEMA bolt pattern for 1/2 hardware. Extra terminal plates allow quick field adjustments and flexibility in designing.

End Frames - Filnor endframes are designed so that the resistors can be mounted in racks or stacked.

Dynamic Braking Stainless Steel Grid Resistor - stamped grid, chomium alloy stainless steel grid resistors - Reliable stainless steel resistor elements and terminals - 8 evenly spaced taps.

Applications: • Crane Control • Dynamic Braking • Neutral Grounding • Harmonic Filters • Mining Equipment • Transit • Load Banks • AC and DC Motor Acceleration

Made in USA

TRW - BWH2R1W Resistor.

Resistance: 2 Ohm.

Power: 1 watt.

Tolerance: 5%.

Material: Phenolic.

Package: axial leads.

Technology: wirewound.

Type BWH. New.

51R7W  Resistor, Metal Oxide.

Resistance: 51 Ohm.

Power: 7 watt.

Mount: Vertical, 4 prong.

Dimensions: 12.0mm (to 12.9mm relaxed) long x 6.9mm wide x 52.00mm max above board.

Vishay - S102C 50K000 - High Precision Foil Resistor, 50.000K Ohms (50,000) 0.01%

The S102C 50K000 0.01% is a through-hole Foil Resistor with Bulk Metal® foil (BMF) technology for applications that require high precision and high stability. BMF technology allows us to produce customer orientated products, designed to satisfy challenging and specific technical requirements. It offers low TCR, excellent load life stability, tight tolerance, fast response time, low current noise, low thermal EMF and low voltage coefficient, all in one resistor. The S series is virtually insensitive to destabilizing factors. The resistor element is a solid alloy that displays the desirable bulk properties of its parent material, thus it is inherently stable and noise free. The S series resistor is the modern generation of precision resistor. The standard design of this resistor provides unique combination of characteristics found in no other single resistor.

Operating Temperature: -55 C t0 175 C

Composition: Bulk Metal Foil

Features: Moisture Resistant 

• Non inductive, non capacitive design
• Non hot spot design
• Lead (Pb)-free or tin/lead alloy terminal finish
• <0.08µH Typical low inductance
• <0.1ppm/V Voltage coefficient
• 0.05µV/°C Typical thermal EMF
• 1ns Effectively no ringing rise time
• Electrostatic discharge up to 25000V
• Voltage Rating 300V
• Tolerance: 0.01%
• 0.6W
• 4.5PPM
• Radial Leads
• Proudly Made in USA