Current Sensor
- KEVLIN - 5089-P - Current Sense Resistor. 0.01-Ohm 4 Axial Terminal Leads, New.
KEVLIN - 5089-P - Current Sensor Resistor. 0.01-Ohm.
Current sense resistors are often referred to as 'shunt' resistors. Shunt resistors are used to monitor the amount of current that is flowing through a circuit. Such resistors have very low resistance values, typically less than 50 milli-ohms (0.050 ohms) and often lower.
A 'Kelvin' configuration resistor features four leads or terminations. These four terminal resistors enable current to be applied through two opposite leads and a sensing voltage to be measured across the other two leads. The Kelvin configuration effectively eliminates the resistance and temperature coefficient of the leads. The Kelvin connection can also simplify board design by incorporating all terminals for the sensing circuit into one part. A Kelvin connection is essential for accurate current sensing and simplified board design.
Tolerance: 1%.
Current Sensing Resistors.
Metal Enclosure
Connections: 4 Terminal Leads, 2 Axial Leads Each End.
Dimensions: 2.25" x 1.25",
Applications:
- General Use - Power supplies, disk drives, battery power management, control of current detection or over-current detection, motor start, high voltage and precision applications.
- Consumer Goods - Power tools, thermostats, appliances, televisions, smoke detectors, and video cassette recorders.
- Automotive - Anti-lock brake systems, keyless entry systems, air bags, power steering control systems, voltage regulators, powertrain, information centers as well as engine controls and modules.
- Telecom - Telephones, cell phones, pagers, mobile radios, hand-held devices and laptops.
- Medical and Instrumentation - Monitoring systems, pressure sensors, implant products, electronic scales, and a variety of diagnostic equipment.
- Military and Aerospace - Satellites, missiles, surveillance equipment, sonar, and avionic products.
- LEM SA - LA55P - Hall effect 0-50Amps AC or DC.Current Sensor. Hall effect 0-50Amps AC or DC. Measuring range- 70 A, secondary signal-50 mA, supply voltage:12-15 Bi, accuracy: 0.9%. Technology : Closed loop Hall Effect. Package: PCB-mounting, 37mm x 25mm x 27mm above board. Learn More
- LEM SA - HA10NP/SP5 - 0-5/10Amp AC/DC Current Transducer - Hall EffectSpecial Price $32.98 Regular Price $42.50
LEM SA - HA10NP/SP5 Hall Effect transducer, open loop.
DC to 50kHz.
PC board mounting.
Galvanic isolation between two primary windings.
Pri nominal: Series: +/-5A Ipn Parallel:+/-10Amp.
Primary current measuring range: Series:0- +/-10A Ip
Parallel: 0 -+/-20A Ip.
Analogue output: +/-4V.
Load resistance:>4kohm.
RMS rated V: 500V.
Supply: +/-15V <20mA.
Specification Sheet Attached.
Dimensions: 19x15x21mmH.
Manuf in the UK.
Either unsoldered or prepped, so we are selling them as if used but guaranteed not DOA.
Learn More - EMPRO - HA-150-100 - Shunt 150 Amp 100Mv.Special Price $29.98 Regular Price $38.50Out of stock
EMPRO - HA-150-100 Shunt
External Portable Shunts 0-150-ADC input 0-100mV to analog meter.
150 Amp 100Mv.
Current: 150 A
Voltage: 100 mV
Resistance: 0.00066666 O
Length: 6.000 in
Width: 1.250 in
Height (Dimension A): 1.380 in
Dimension B: 0.500 in
Distance Between Mounting Holes: 5.250 in
Mounting Hole Diameter: 0.200 in
Learn More - LEM SA - HA10-NP/SP1 - Current Transducer 0-5/10 Amp AC/DC. Hall Effect.Special Price $68.98 Regular Price $94.50
LEM SA - HA10-NP/SP1 Current transducer 0-5/10Amp AC/DC.
Open Loop Hall Effect Transducer DC to 50kHz.
Galvanic isolation Between Two Primary Windings.
Pri Nominal: Series: +/-5A Ipn Parallel:+/-10Amp.
Primary Current Measuring Range: Series:0-+/-10A Ip Parallel: 0-+/-20A Ip.
Analogue Output: +/-4V.
Load Resistance:>4kohm.
Rms Rated V: 500V.
Supply: +/-15V <20mA.
Case: PC board mounting 19x15x21mmH.
Spec Sheet Attached.
Learn More - Honeywell MICRO SWITCH - CSLF4HG - Linear Current Sensor 73AmpDC 4-20mA-OutSpecial Price $148.98 Regular Price $185.00Out of stock
Honeywell MICRO SWITCH - CSLF4HG - Linear Current Sensor
DC / DC Enclosed Sensor with 4-20mA Output.
Supply Voltage: 10.5-24VDC
Supply Current: 30mA
Max Sensed Current 147A-peak
Adjustable Operating Range
New in Manufacturer's Packaging w/Specification
- EMPRO - MLB-400-50 - MSA401 - Shunt, 400 Amp, 50mV.Special Price $19.98 Regular Price $24.50Out of stock
EMPRO - MLB-400-50 - MSA401 Shunt.
A commercial shunt designated by Empro as Type MLB. These shunts are used when size and weight are a major design consideration. These shunts comply with MIL-S61-B and commercial item description AA55524.
400Amp 50mV.
0.000125 Ohms
Learn More - EMPRO - MLB-300-50 - MSB301 - Shunt - Shunt. 300Amp 50mV.Special Price $19.98 Regular Price $24.50
EMPRO MLB-300-50 - MSB301 - Shunt.
A commercial shunt designated by Empro as Type MLB. These shunts are used when size and weight are a major design consideration. These shunts comply with MIL-S61-B and commercial item description AA55524.
300Amp 50mV.
0.000166666
Learn More - EMPRO - MLB-250-50 - MSB251 - MLB Shunt - Shunt. 250Amp 50mV.Special Price $19.98 Regular Price $24.50
EMPRO - MLB-250-50 - MSB 251 - Shunt.
A commercial shunt designated by Empro as Type MLB. These shunts are used when size and weight are a major design consideration. These shunts comply with MIL-S61-B and commercial item description AA55524.
250Amp 50mV.
- EMPRO - MLB 170-50 - MSB171 - Shunt. 170Amp 50mV.Special Price $19.98 Regular Price $24.50
EMPRO - MLB 170-50 Shunt. MSB171
A commercial shunt designated by Empro as Type MLB. These shunts are used when size and weight are a major design consideration. These shunts comply with MIL-S61-B and commercial item description AA55524.
170Amp 50mV.
0.00029411 Ohms
Learn More - EMPRO - MLB-150-50 - Shunt 150 Amp ,50mV.Special Price $19.98 Regular Price $24.50
EMPRO - MLB-150-50
A commercial shunt designated by Empro as Type MLB. These shunts are used when size and weight are a major design consideration. These shunts comply with MIL-S61-B and commercial item description AA55524.
Shunt. 150Amp 50mV.
Learn More