Other Sensors

OPTEK - KS3175 - Photodiode.

Body dimensions: 1/8" D.

Package: Hermitically Sealed

Domed Lens

Contact: Single Lead,

Pin 1" Gold Plated.

Applications: Non-contact reflecƟve object sensor, Assembly line automation, Machine automation, Machine safety, End of travel sensor, Door sensor

NAMCO LEUZE Danaher - EP130-14231-TTL - Infrared Slim-Line Photo Electric Sensor / Scanner

Status: Discontinued Photoelectric Eye

12-24VDC

Photoelectric 200MM NPN 24VDC RK72/2 200

Diffused Scanner

Input Modulated LED

Adjustable Sensitivity

Reverse Polarity & Short Circuit Protected

Factory New

Made in Germany

HONEYWELL Micro Switch - 26PCCFA1D Presure Sensor, PCB Mount.

The 26PC Series Miniature Pressure Sensors are small, cost-effective devices intended for use with wet or dry media. These sensors feature proven sensing technology that uses a specialized piezoresistive micromachined sensing element to offer high performance, reliability, and accuracy. Each sensor contains four active piezoresistors that form a Wheatstone bridge. When pressure is applied, the resistance changes and the sensor provides a milliVolt output signal that is proportional to the input pressure. The low power 26PC sensors are designed to accommodate pressures from 1 psi to 250 psi and have an operating temperature range of -40 ºC to 85 ºC [-40 ºF to 185 ºF].

Status: Discontinued

Pressure Range: Differential, 0-15 PSI

Seal Material: Flurosilicone

Pressure Type: Straight Port

0-100MV Output.

Non-Temperature Compensated Output

Silicon Sensor Chip

10-16VDC.

Dimensions: 1.35 Lx 0.5W

Operating Temperature: -40 C to 85 C

Gage 0.86 L, 4-leads.

Applications: Medical, Industrial, & Commercial.

More Information: https://sensing.honeywell.com/honeywell-sensing-trustability-board-mount-pressure-sensors-tsc-nsc-datasheet-50064366-d-en.pdf

Proudly Made in USA

Allen Bradely ELECTRONIC CORP AMERICA - 42MRR-5000 - Photohead Receiver Sensor.

Photoswitch Beam (A/B) Green Line

Power supply: Type 42MTB bases.

Output: See Output Module.

• 25.4-171MM RANGE
• LIGHT/DARK OPERATE
• 880 NM INFRARED LED
• IP66

Note: Allen Bradley (Rockwell International) purchased Electronic Corp America.

New Old Stock

UPC: 662073836865

Texas Instruments - TIL99 Transistor, NPN InfraRed Phototransistor, Foto Transistor, Pyrometric Sensor.

Max voltage: 50Vcb, 30Vce, 7Veb.

Status: Discontinued

Dark Current-Max: 100.0  nA

Mounting Feature: THROUGH HOLE MOUNT

On-State Current-Max: 0.05  A (50mA-Ic)

Operating Temperature-Min: -60.0  Cel

Operating Temperature-Max: 125.0  Cel

Power Dissipation-Max: 0.25  W

Response Time-Max:  8.0E-6  s

Package: TO-18 Gold Lead, Hermetically Sealed.

Note: Case is Collector.

Spectrally & Physically matched with TIL31 GaAs Near-IR 940nm Emitters.

Alternates: ECG3032, NTE3032

GV CONTROLS INC - FSX-2104.

Air Flow Sensing Switch

SPST NC 24V NC,

Case: 43.2mm tall x 20.4mm D, 9 pin.

Made in USA

Military 5945-005655998.

ELECTRONICS CORP. OF AMER - 42MRL-5000 -  LED Source Photohead Sensor.

Status: Discontinued

Power Supply: Uses Type 42MTB base.

Switch Trans Beam

Output:Green Line, 25.4 mm - 171 m

(1 in - 560 ft) Sensing Distance

Response Time: 2.5mS

New Old Stock

Made in USA

Clarostat Honeywell SKAN-A-MATIC - T21007 -  Photoelectric Amplifier Scanner Control Module

The T21007 photoelectric amplifier module is designed to amplifieroutput from a photodetector. The output of the photodetector is taken as the input of the module.

Status: Discontinued

Features:
■ Modular approach
■ Printed circuit board mounting
■ Low power consumption
■ Small size
■ Gold plated leads
■ Epoxy encapsulated

Mount: PCB 

Connections: 10 Square Pins

New Old Stock

Made in the UK

KEYENCE - AT-210 - Digital Contact Sensor Amplifier Control Module.

Status: Discontinued

Output Voltage: -0.5 ~ +0.5 V.

Output Impedance: 300 Ohm.

Supply voltage: DC12-24V, 10% ripple (PP) 10%.

Measurement Range: -5.0 to +5.0 mm-0.197" to 0.197"

Analog Output Voltage

Output Voltage:  -0.5 to +0.5 V

Impedance: 300 Ω

Resolution: 10 µm 0.39 Mil

Linearity: 0.8% of F.S.

Response: DC to 800 Hz (-3 dB)

Measurement Force: 0.28N*1

Temperature Characteristics: 0.03% of F.S./°C*2

Connection Cord Length: 3 m

Power Voltage: 12 to 24 VDC ±10 %, Ripple (P-P) 10 %

Current Consumption: 50 mA or less

Ambient Temperature: 0 to +50 °C 32 to 122 °F

Relative Humidity: 35 to 85 % RH (No condensation)

Din Rail Mount

Dimensions: Width:7.00 (in)Height:6.00 (in)Depth:7.00 (in)

Weight: Approx. 100 g

Complete with a 4 conductor cable 9 foot, and attached 4 pin male micro connector.

Made in Japan

New

TELEMECANIQUE - XUE-H3000 - Photoelectric Sensor Emitter. Package of 2.

Status: Discontinued

Photoelectric Emmitter 

Through Beam: 30m

Voltage: 12 - 48v with protection against reverse.

Switching Capacity: </= 200mA with Overload and Short Circuit Protection.

Protection: IP 67

Operating Temperature: -25 C to 70 C

Connections: Screw Terminals

Max. Switch Frequency: 30 Hz

Note: Used / Removed from Equipment. 

Note: Highly discounted due to cracked replaceable cap on one sensor.

Approvals: CE, CSA, UL

Package of 2

WattStopper - HB350W-L3 - High Bay Passive Infrared Occupancy Motion Sensor for Wet Locations

The HB350W-L3 High Bay Passive Infrared (PIR) Occupancy Sensors for Wet Locations consist of a sensor and a lens
module. Designed for automatic lighting control in warehouses and other medium and high bay wet location applications.

The HB350W-L3 occupancy sensors are designed to mount to a light fixture and control one load in that fixture. They can be wired to control all ballasts in the fixture, or to control half of the ballasts, providing high/low lighting control. When motion is detected within the sensor’s coverage area, the relay in the sensor closes, and lighting loads are automatically turned on. When motion is no longer detected for the duration of the time delay setting, the relay opens and the lighting load is turned off. The sensor’s sensitivity and time delay settings are factory preset at “normal” and 15 minutes, respectively, which are suitable for high
bay applications. However, if the values need to be adjusted for specific applications, they can be easily changed using the DIP switches on the unit.

Weight: 6 Ounces

UPC: 754182924042

Additional Information: 

https://www.mc-mc.com/ASSETS/DOCUMENTS/ITEMS/EN/WattStopper_HB350W_L3_Installation_Instructions.pdf

https://assets.usesi.com/product-media/brochures/500654_brochure.pdf

New

Rolling Ball Tilt Switch. Direction indicating Switch, TO-39 style case. Gold plated leads, and internal contact ball Highly Sensitive to detect basic motion/orientation. Environmentally safe, non-mercury electronic switch. Sealed type available for heavy humidity environment, free from bad connection problem caused by contact oxidization. Poor man's accelerometer. 

An internal gold-plated ball inside the sealed case touches one of 4 leads when tilted about 25-degrees or more. Since the leads are 90-deg apart you can sense which direction the device is leaning or tie the 4 together and any shaking or movement off level will cause contact closure. Has four leads on the bottom and one on top.

Rolling Ball Tilt sensors allow you to detect orientation or inclination. They are small, inexpensive, low-power and easy-to-use. If used properly, they will not wear out. Their simplicity makes them popular for projects, toys, gadgets and appliances.

Typical Applications - Alarms, Safety, Security, Directional Position, Vibration, Movement Detection.

Last picture shows dissected TO-39 case to show internal gold plated ball and four contact leads.

Significant discounts in Quantity purchases of 100, 300 or more.

TELEMECANIQUE - XUE-H307534 - Photoelectric Sensor Receiver.

Status: Discontinued

Photoelectric Receiver

Through Beam: 30m

Voltage: 12 - 48v with protection against reverse.

Switching Capacity: </= 200mA with Overload and Short Circuit Protection.

Protection: IP 67

Operating Temperature: -25 C to 70 C

Connections: Screw Terminals

Max. Switch Frequency: 30 Hz

Note: Used / Removed from Equipment. 

Approvals: CE, CSA, UL

XUE-H307534 is replaced by XUXOAKSAM12

Clarostat Honeywell SKAN-A-MATIC - T31101 - Photoelectric Amplifier

Features:
■ Open collector output
■ Plug-in 8 Pin Plug
■ Output indicator LED
■ 15 turn sensitivity adjustment
■ May be wired LIGHT or DARK energize
■ 5 VDC Input

5VDC Sensor Amplifiers Photoelectric Amplifiers Open Collector Output capable of loads up to 250ma. @ 28vdc maxPlug in mount LED Output Indicator

New Old Stock

Made in USA

Philips - NXP - RPW100 Sensor, Pyroelectric Detector, Photoconductive Infrared.

Dual-Element Motion Detector with 6.5 -14 µm Bandpass.

One Channel. 

Photosensitive Area 2.0= (mm2).

Spectral Response Low: 6.5u=(m).

Spectral Response High: 14u=(m).

Re Min.(V/W) Responsivity=23.pyroelectric 

Element Operating Temperature: 22.

Package: TO-39 var. Gold Base and Leads

Made in United Kingdom

Note: Amperex P/N: 4-53044-2.

Pepperl & Fuchs - UB500-30GM-E0-V15 - Sensor, Ultrasonic. Switch output: NPN NO/NC.

Housing Material: Brass

Number of Pins: 5

Frequency: 380 kHz

Operating Temperature: 1-25C to 70 °C

Max Supply Voltage (DC): 30 V, Min Supply Voltage (DC):20 V

Response Time: 480ms

Switching Current: 200 mA

Termination: Connector

Dimensions: Diameter 30 mm, Length 94 mm, Thread Size M30

Ratings: IP65

RoHS Compliant

New in Manufacturers Packaging

Honeywell MICRO SWITCH - CSLF4HG - Linear Current Sensor

DC / DC Enclosed Sensor with 4-20mA Output.

Supply Voltage: 10.5-24VDC 

Supply Current: 30mA

Max Sensed Current 147A-peak

Adjustable Operating Range

New in Manufacturer's Packaging w/Specification

Meriam Instruments - 5-458 - Complete Oxygen Sensor - O2 Board Only w/Humphrey P5098 Valve.

Complete Oxygen Sensor - O2 board only.

No Case.

Includes P5098 valve and 80C32.

Proudly Made in USA

KEYENCE - PS-49 - Reflective Sensor Head, General-purpose Type, Long-distance

Type: Definite reflective

Detecting distance: FINE - 32 to 53 mm 1.26" to 2.09"

Light source: Red LED

Environmental resistance; Ambient temperature -10 to +50 °C 14 to 122 °F (No freezing)

Relative humidity; 35 to 85 % RH

Weight Approx. 30 g 

LONG RANGE PHOTOELECTRIC SENSOR 32-53mm Definite-Reflective 1.5mm Red beam spot simplifies positioning the sensor. Targets 0.1mm in diameter can be detected from 50mm - NEW TWO LENS SENSORS WITH 10FT CORD

New

Cutler-Hammer / Eaton - 6200AS6505 - Photoelectric Sensor Reflector

Retroreflector, Clear.

Screw Mount

Dimensions: 2.18 Diameter.

Series A1

UPC 78-2114-216774.

Alternate: Newark 44K9658

Cutler-Hammer Eaton - 1310AS9272 - Comet 18mm Tubular Photoelectric Sensor. 

Forward Viewing, Sensor Distance 2 inch

100 mA PNP, 250 mA NPN max DC

NPN/PNP Open coll, 100 mA PNP, 250 mA NPN at 10-30 VDC

Operating Temperature:  -40 C to 158 C

4 Pin Dual Key Micro Connector

Background Suppression, 8 in(.2m)

Series A3, Double Marked 06123.

Environmental Rating: NEMA1,3,4,4X,6,6P,12,13, IP68, IP69K

Dimensions: Height: 2.6" Length, 0.47" Width: 0.71"

Weight: 0.1313 lbs.

Complete with Users Manual and Mount Hardware.

Factory New Difficlut Component to Find.

UPC 782114648377

Cutler-Hammer Eaton - 13104RS9272 - Comet Series 8 mm Tubular Photoelectric Proximity Sensor

Construction Style: Barrel/Tubular

Right Angle Viewing

10-30VDC AC/DC

Sensing Range: 0.40" to 1.80" (10 to 45mm)

4 PIN AC/DC Micro Connector

Material: Polyurethane

Beam Type: Visible Red

Operating Temperature: -40 F to 158 F (-40C to 70 C)

Micro-Connector series A3 07071.

Dimensions: 3.02" X 0.60" X 0.71"

Eaton/Cutler-Hammer.

UPC 782114648360

Banner Engineering Corp - D12EP6FP - 41965 - Sensor, Fiber Optic.

D12 EXPERT Series: Plastic Fiber Optic

Cable Length (m): 2

Power: DC

Accepts Fiber Termination Type Unterminated Plastic Fibers or T5 Termination

Housing Style: DIN Rail

Primary Housing Material: Thermoplastic

Input/Output: Discrete

Color LED – Amplifiers: Red

Fiber Type: Plastic and Glass

Output: PNP

Connection: Cable

Quick Disconnect Type: No QD

Output Type (Specific): Single Discrete

Repeatability (µs): 66

Number of Pins: 5

IP Rating: IP11

NEMA Rating: NEMA 2

Op. Temperature (°C): -20 to 70

Max Op. Relative Humidity (%): 90% @ 50°C

Special Feature: Remote Teach  Yes

Intrinsically Safe: No

Adjustments: Teach Button

Power Supply/Supply Voltage: 10-30 V dc

Delay at Power-up (ms): 100

Indicator Display Type: Bargraph

Factory new in Manufactures Packaging.

Newark: 20H5782

Grasslin - BT-120 - Photoelectric Switch, Flush Mount, SPST NC, 120VAC, 50/60Hz, 1500W, 1200VA

Photoelectric switches control the power to a connected appliance or fixture by measuring the light falling on the lens (also called the "eye"). These switches are mostly employed in outdoor locations to allow lights to turn on automatically after the sun has gone down.

Status: Discontinued

Grasslin Photocontrol Flush Mounting

Heavy Duty Commercial Model BT-120 Photoelectric Sensor, Button Type

Power: 120VAC 50/60Hz, 3 Wire 

Switch: SPST Normally Closed (NC)

Switch Capacity: 1500 Watts Tungsten

Switch Capacity: 1200 VA Ballast

Raintight Enclosure

Dusk To Dawn Operation

Housing: Black Thermalplastic

Operating Temperature: -40F to 140F ( -40C to 60C)

Mounting Hole (Minimum): 11/16" (0.688) (17.49mm)

Thicknees Mount Surface (Maximum) : 3/8" (0.375") (9.54mm)

Approximate Body Dimension: 2.0" Long X 1.0" X 0.80"

Applications: All night Safety and Security for walkways, entrances, parking lots, farm yard lighting, recreational areas. Protection Control for homes, schools, commercial and industrial buildings.

In Manufacturing Packaging with Instructions. 

UL, CSA Listed

UPC 147305930

Replaces: Paragon LB201-00, Intermatic K4021, Tork 3000, ALR AA-105, Fisher Pierce FA-105, Precision A-105