Featured Products

EATON CUTLER HAMMER OPCON - 1550B-6501 - Photoelectric Fiber Optic Sensor.

Enclosure Material: Body: Noryl, Lens: Nylon

Environmental Rating: NEMA 1,3,4,12,13

Input Voltage: 90-132 Vac

Led Indicators: Red output status

Operating Mode: Fiberoptic, Infrared

Operating Temperature: -40° to 158°F (-40° to 70°C)

Sensor Type: Fiberoptic

Switch Type: Photoelectric

Alt P/N: 106983.

UPC 782113825595

Made in USA 

New

Learn More

I/O relay board, mounting rack. G4, with head connect, brain board compatible, 32 channel/B4 brai. Learn More

OPTO 22 - G4IAC5A Relay, I/O. 5V logic.

Input: 240VAC.

Red LED. 

Mount: 5 pin PCB or I/O rack.

Learn More

Relay, I/O. Isolated output: 0-5V. Mount: PCB or I/O rack. Learn More

CUTLER HAMMER OPCON - 8713A-6501 - Relay, One Shot.

Alt P/N: 102166.

Plastic Enclosure.

Made in USA

New

Learn More

Photoelectric control. Fiberpak. 5-30VDC 100us. Designed for equipment manufacturers that use microprocessor based control system. Alt P/N: 109300-003. Plug-in module. Learn More

Type 3 media filter with 25 foot cable and an RJ-22 connector. Learn More

Relay, AC. 4PDT Coil: 200/220VAC, 5A240VAC, 5A28VDC. Plastic enclosed, plug in. Termination: solder. Listed: UL/CSA. Learn More

Thru beam fiber optic cable. Learn More

Switch, limit. Head and switch body only. For Omron heavy duty limit switches, standard side. Learn More

DIP RELAY NEW 48VDC Learn More

EATON CUTLER HAMMER OPCON - 8211A-6501 - Plug-in Logic Module, Time Delay Logic Card.

The 8211A Time Delay is an optional logic card for Opcon's 1411D and 1311D Control units.

50 ms to 5.0 sec.

LT or DK mode.

Factory New

Made in USA

Learn More

EATON CUTLER HAMMER OPCON - 8211A-6501 - Plug-in Logic Module, Time Delay Logic Card.

The 8211A Time Delay is an optional logic card for Opcon's 1411D and 1311D Control units.

50 ms to 5.0 sec.

LT or DK mode.

Factory New

Made in USA

Learn More

OPCON - 6141A-6501 Hardware. Swivel Mount Bracket.

Material: Aluminum

Part Number: 102385

For use with 11 Series Controls.

Operating Temperature: -40° to 158°F (-40° to 70°C)

Proudly Made in USA

Learn More

THREADED HEAD Learn More

Sensor. Photoelectric head, range 15-23 feet. Complete with attached single ended cable. Note: Alt P/N: 101896. Very clean, maybe gently used. Learn More

Switch hardware. Learn More

OHMITE - 412-B - Power Tap Rotary Switch - 1 Pole, 3 Position, 50Amp 300V.

Configuration: SP12T

Current / Voltage Ratings: 50Amp 300VAC, 50Amp 20VDC.

Contacts: Silver Alloy

Body: Ceramic

Angle of Throw 30 Deg.

Mount: 1/4" Panel. A 5/16” hole in panel is required for shaft.

Actuator: Flatted (6.35mm D).

Dimensions: 4 3/16" Width 

Mounting:Three 10-32 flat-head machine screws 3/8” long. 

Note: Power Tap Switch.

Connections: Solder Lug.

Used / Removed from Equipment - Good Condition

Made in USA

 

Learn More

OHMITE - C300KR80 - Resistor, Corrugated Ribbed Tubular Ceramic.

Corrib® resistors are ideal for applications involving high currents at very low resistance values. These large, heavyduty resistors are designed to withstand frequent start-stop cycles characteristic of motor starting, dynamic braking and other similar applications.

Technology: Industrial Wirewound Ribbed, Series 280.

Resistance: 0.8 Ohm. (800 mOhms)

Power: 300 watt.

Tolerance: 10%.

Maximum Voltage: 1000.

Operating Temperature: 25 C to 400 C

Temperature Coefficient: 400 PPM/C

Mount: Chassis

Termination: Lug

Dimension: 1-1/8" D x 8-1/2" Long. (216mm Long)

Note: Ribbed construction for enhanced cooling.

Vitreous Enamel, Corrugated Resistive Wire.

More info: https://www.ohmite.com/assets/docs/res_280.pdf

Alternates: E300KR80E, E300KR80, Mouser 588-C300KR80, Newark 6H5214

New Old Stock - Made in USA

Learn More

Rotary shaft encoder. Learn More

Hydraulic/Pneumatic. Air cylinder 3-1/4 Bore 1" Stroke from 0.75" D Threaded shaft - mounted on steel plate 5.5 x 3.75", about 8" long overall, 3.75" square. Learn More

OAK INDUSTRIES - 3-251 Switch, Rotary.

Robust switch designed for commercial applications. Some advantages to open frame construction are that the switches have more flexibility on custom contact configurations and that they have sections that are sold separately. Shorting describes the action of the contact when you select your switch positions. With a non-shorting switch the connection is momentarily broken when you rotate from position 1 over to position 2

Contacts: 5 Position.

Connection: Solder Terminals.

Mech: Panel, 3/8" bushing.

1.5A @ 28VDC

Genuine Vintage Oak Industries - New Old Stock

Age related tarnish on silver contects does not impact operation.

Proudly Made in USA

Body: 1.532 (38.9mm) D x 651" (16.5mm) high plus seated bushing 0.378" (9.6mm) long, shaft 1/4" flat 0.329" (8.33mm) long.

Note: Phenolic wafer. PLEASE READ AND COMPREHEND PRIOR TO WIRING SWITCH! The contact switching arrangement is as follows. Terminal positions are numbered counterclockwise from the rear view of the switch. There are 24 physical segments. Orient the rear of the switch so that the mounting screw nuts are above the arc of rear side contacts with 4 terminals including two wipers. Start numbering immediately right of the left nut, being position 1 and increasing counterclockwise. Terminals on the visible side have even numbers and those on the other side have odd numbers. Empty holes are numbered as well. There are four wipers on the switch at positions 1, 2 , 10 and 13. Position 1 [No contacts are connected] Position 2 [1-3 and 13-15 are connected]Position 3 [1-5 , 13-17 and 10-16 are connected] Position 4 [1-7, 13-19 and ,10-18 and 2-6 are connected] Position 5 [1-9, 13-21 and 2-8 are connected]All contacts are non-shorting [break-before-make)

Learn More

Relay, reed. Package: 4 Pin. Learn More

Motor, controller. VariSwitch, variable limit controller. 21~36VDC Input - Requires handheld control box with EEPROMs, not included. Protective wiring paper seal still in place. NIB. S/N 12601242. Learn More