Stepper Motors

PORTESCAP - GC26M048A30V Motor, Stepper.

Tiny 5V miniature, with heavy 10:1 gear box.

4-Phase 6-wire UniPolar,

Dimensions:only 1.1" [28mm] x 1.43" [36.2] x 1" [25.4]

Shaft: 3mm knurled shaft 7.5mm long.

Mounts on two threaded holes on 30mm centers.

RoHS Compliant.

Note: Danaher / Portescap.

Weight: 1.8 oz.

Learn More

Siemans Airpax - L82401-P2 Motor, Stepper.

Commercial Series High quality Permanent Magnet Stepper Motor with 7.5 degree step angle. The motors may be fitted to a gearhead where increased torque and resolution are required at reduced operating speed. Four phase motor suitable for use with uni-polar drive circuits. Ideally suited to instrumentation applications.

DC Operating Voltage: 12VDC

Resistance per Winding 52 ohm.

Steps per Revolution: 48 

Resistance per Coil: 9.1 Ohm 

Step Angle: 7.5 degrees.

Connections: 6 Wires

Holding Torque: 4.5 Ncm

Mounting: 1-3/8" Hole Spacing.

Rotor Inertia: 0.0118 Kgcm2

Current per Phase: 0.16 Amp

Inductance per Phase: 37.7 mH

Max. Operating Temperature: 100 C

Ambient Operating Temperature: -20 C to 70 C

Bearing Type: Sintered Bronze Sleeve

Body: 42mm Diameter.

Shaft: 3mm Diameter x 9.6mm Long.

Mount Plate, 4 holes, 35mm centers.

Weight: 4.8 oz.

Made in Malaysia

New Old Stock

 

Learn More

Motor, stepper. 15V 4 phase 0.49Amp. 48 step/rev. 8 wires.

The SLO-SYN motor is unique in that it has the capability of being operated as an AC synchronous, constant speed motor or as a phase switched DC stepper motor. In either case, it is classified as a permanent magnet inductor motor.

Danaher Motion - SLO SYN product line is not out of manufacture. 

Mounting: 2.2" hole spacing.

Body: 2.75" square (70.5mm) x 1.75" high (46mm).

Shaft: 1/4" D x 0.63" L.

Weight: 1.3 lbs (22 oz).

Note: Slo-Syn.

Very compact for amount of torque. 8-wire = 4-phase = Unipolar.

Made in USA

Learn More

SUPERIOR ELECTRIC CO. - SLO-SYN - MP70-9A-Z9-9Z-017 Synchronous Stepping Motor, 5.2VDC 1.44Amp. 48 step/rev.

Superior Electric is recognized worldwide as the leading manufacturer of step motor positioning systems. Over 40 years ago, Superior Electric developed and patented their SLO-SYN® Step Motor products.

The SLO-SYN motor is unique in that it has the capability of being operated as an AC Synchronous, constant speed motor or as a phase switched DC stepper motor. In either case, it is classified as a permanent magnet inductor motor.

Status: Danaher Motion - This SLO-SYN P/N is Discontinued.

Slo-Syn. 8-Wire 4-Winding.

Rating: 5.2 V@1.44 Amps

48 Steps per Revolution

Very High Torque.

Bobbin Wound Stepping Motor. Patent 4,349,957

Mounting: 2.28" Hole Spacing.

Body: 2-3/4" D x 1.7" L.

Shaft: 0.25" Diameter w/flat 0.6" Length

 2.75" Square Mounting Plate with 4 holes with Threaded inserts, about 2.28" apart.

Very compact for amount of torque. 8-wire = 4-phase = Unipolar.

Weight: 1.5 lb (23 oz).

New Old Stock

Made in Japan

Learn More

Stepper motor for Epson 4-Wire Two 9-Ohm Coils on ribbon cable - 1.65"/42mm Diameter - 24mm tall - mounts on two holes 50mm apart - gear on 2.9mm shaft is 8mm Diameter - NEW Learn More

Applied Motion Products Inc  - 4017-838  - 776619324 - Precision Unipolar Stepper Motor

A unipolar stepper motor has two windings per phase, one for each direction of magnetic field. Since in this arrangement a magnetic pole can be reversed without switching the direction of current, the commutation circuit can be made very simple (eg. a single transistor) for each winding.

Status: Discontinued 

12VDC Stepper Motors 0.16Amp

100 Steps/Rev 3.6Deg/Step

4-Phase 75-Ohm,

Torque: 700 Ounce/Inches

MPI SPEC# 77619324

Dimensions: 42mm Square x 33mm Deep

Mounting: 2-slots 62mm apart on 55x78mm flange

Shaft: 4.9x11.1mm 

Unipolar 6-Pin Connector (5 wires)

Made in Japan - New Old Stock

Application: Robotics

Learn More

AIRPAX - 82227/B82359 - Motor, Stepper. 12VDC 2 Phase 37 ohm.

Motors, Stepper.

Simple 2-phase, 12VDC 48 Step/Rev 7.5deg/step, 37 Ohm Bipolar Windings.

Dimensions: 35mm, 1.38" D. Attached: 4 Wire Bipolar, 16 inches long.

Mounts 1.7" 42mm hole spacing, includes a 15-tooth 1/4" Diameter Nylon Gear.

Running Rate to 1800 step/sec.

Weight: 2.6 oz.

New Old Stock

Proudly Made in USA

Learn More

Airpax Sensata - A82454-M3 - Motor, Unipolar Stepper - 5VDC 1.125 Deg/Step 0-400RPM 0-320P/Sec.

The stepper motor is a device used to convert electrical pulses into discrete mechanical rotational movements.

Supply: 5VDC.

Speed: 0-400 RPM.

Winding Resistance: 15 Ohm.

Steps: 1.125 Deg/Step. 3.5Watt,

Wire Count: 6 Leads.

Mech. Mtg: Two (2) Mounting Holes 2.38"apart.

Body Dimensions: 2.12" x 2.75" x 1.4" with gear attached to 1/8" shaft.

Weight: 7 oz.

Note: 0-320P/Sec, 3.5 watt.

Rotation: Reversible.

Made in USA

New Old Stock 

 

Learn More

Motor, Stepper, Dual-shaft. Supply: 3.0VDC 2.7A. Steps: 200 steps per rev. Direction: Reversible. Wire count: Internal-connections 4-terminal. Mech. Mtg.: 90mm frame NEMA 34D. Body Dimensions: 3.36" [85mm] square x 6.2" [158mm] with both shafts, One 0.50"D double flat and one 0.375"D keyed. Connect per 213803. Two-phase, single stack. Weight: 5 lbs. Warner Electric / Superior Learn More

SUPERIOR ELECTRIC CO. - PDT500-1001 - SLO-SYN Positioning System.

Stepper motor Drive combined with a Micro-series Indexer.

New, in box with manual.

Learn More

Panasonic MATSUSHITA - 55SI-25D AWC Motor, Stepper.

12V 36 Ohm 7.5 Deg 6 Wire.

Dimensions: 2.042" (51.8mm) D body, overall with mount 3.138" (79.7mm) long.

Heatsink is 2.955" (75.0mm) wide x 1.027" (26.00mm) high.

Shaft 1/4" half flat x 0.750" (19.0mm) long.

With attached 6 position female header connector.

Silicon Grease is between the motor the heatsink.

Weight 11 oz.

Note: Arduino driven using low cost driver IC ULN2003 transitor array also in our stock.

For More Detals Rreference: https://arduinodiy.wordpress.com/tag/stepper-motor/

Manufactured by Matsushita for Coleco Adam.

Made in Japan

Learn More

LEDEX - 5945-636-5462 - B-61986-A - Rotary Solenoid Switch -Motor, Stepper with Switch/Return Spring.

Rotary Selector Features

Compact Design
High Torque to Size
Snap Action On/Off
Return Spring

Type: Base End Shaft, Ratcheting Rotary Solenoid

Supply: 48VDC.

Body Dimensions: 1.90"D x 2.74"H.

Mount: 3 Tapped holes

Weight: 12oz.

With Wafer Switch.

Additional Information: https://www.ermec.com/catalogos/2017/saia/Rotary%20DC%20Solenoids%20mm.pdf

Military NL-71277-3-2, B-61986-A

Made in USA

Learn More

Sensata Industries - AIRPAX - L82101-P2 Motor, Stepper.

12V 118 Ohm

15 deg/step.

6 wires.

Mounting: 1-3/8" hole spacing.

Body: 1"D (25.5mm) x 1/2" (12.6mm) deep, with 35mm mount centers.

Shaft: 1.7mm D x 8.7mm L.

Weight: 1 oz.

New Old Stock

Proudly Made in USA

Learn More

Motor, Slo-Syn stepper. Supply: 9VDC. N/P Current: 1.53A . Steps: 200 steps/revolution. Torque: 225 Oz-In. Direction: reversible. Wire count: 6. Mech. Mtg: 3-hole mounted to 4-hole plate. Shaft: has a removable pulley attached. Weight: 8 lbs. Learn More

SUPERIOR ELECTRIC CO. - M063-FD09C2 - Motor, Stepper.

Supply: 2.25VDC 4.6A.

SLO-SYN Synchronous Stepper.

Nema Frame 23

Torque: 100-Oz-In.

Inertia: 0.11 Lb in2

Direction: Reversable, 200 Steps per Revolution.

Wire Count: 6-Wires, Wired to Connector.

Dual Shaft.

New Old Stock

Learn More

Motor, Stepper, Dual-shaft. Supply: 3.0VDC 2.7A. Steps: 200 steps per rev. Direction: Reversable. Wire count: Long wire cable to Internal-connections 4-terminal. Mech. Mtg.: 90mm frame NEMA 34D. Body Dimensions: 3.36" [85mm] square x 6.2" [158mm] with both shafts, One 0.50"D double flat and one 0.375"D keyed. Connect per 213803. Weight: 5 lbs. Two-phase, single stack. Learn More

Motor, stepper. Slo-Syn. Supply: 3.0V. Current: 3.0A. Torque: 180 Oz-in holding. Dual shaft SPEC.A213803. NEMA34D. Learn More

Motor, Stepper SLO-SYN. Supply: 6.93VDC 1.5A . Steps: 200 steps/revolution . Torque: 300-Oz-In. Mech. Mtg: 3-hole mounting 2.8" spacing. Body Dimensions: 110mm NEMA 42. Shaft: 0.38"D Learn More

Cords & Plug sets. For Slo-Syn motors. I/O Cable for Slo-Syn motors. BCD I/O cable, 25 pin D, 10 foot (3 meters). Learn More

I/O Cable for Slo-Syn motors. BCD I/O cable, 25 pin D, 5 foot (1.5 meters). Learn More

PACIFIC SCIENTIFIC - E33NRHT-LNF-NS-00  65V 5.1A NEMA 34 Hybrid Bipolar Parallel Stepper Motor

Danaher Motion

Status: Discontinued

Po:176W 5.1A BIPOLAR PARALLEL

1.8DEG/STEP

9.6mm flatted shaft [with threaded hole in end] x 29mmL

STEPPER MOTOR 86mm dia x 128mmD 80mm mounting flange, 69mm centers

Note: One has a Pulley attached

New Old stock 

9 Lbs.

Additional Information: https://www.artisantg.com/info/Pacific_Scientific_Step_Motors_Datasheet.pdf

Proudly Made in USA

Alternate: 10-16976

 

Learn More

Motor, stepper. Hybrid. 35VDC 5.4Amp 1.8 Deg/Step 88 watt 1500RPM. bipolar-Parallel. Sigmax [Flux Focusing increases torque}. Shaft: 9.6mm/0.38" D shaft x 30mm long, 4-lead parallel. Max torque at low speed 500-PPR w/ line driver. Holding Torque: 223-349-oz-in [1.58~1.90nM]. Nema-34, 3.4" square frame. Two MS connectors; 5 Pijn male and an 8 Pin male. Made in the USA. Learn More

12VDC 4.25W 6-lead Bifilar 15-degree Stepper Model #ABS Part #3007-001 Reduction: DD - Volts: 12DC Step Angle: 15-degrees. Mounts with two holes on 2.38" centers, pear shaped gear cup Instrument Motor 0.125" shaft half an inch long. Some instructions supplied. Learn More

42mm dia x 14.5mm thick, 2.9mm shaft 11mmL with 6.2mm 10-tooth brass Gear 4-hole plate, 35mm centers Stepper Motor 4-Wires, 19"long very thin 3.6oz Learn More