Heaters

Heaters. Flexible thermofoil 24VDC 21 Ohm. Mount: easy-to-install adhesive. Dimensions: 14.25" x 0.80" x 0.018" with 56" long teflon 30AWG wires. Learn More

Heaters. Flexible thermofoil 24VDC 21 Ohm. Mount: easy-to-install adhesive.Dimensions: 0.8" wide x 14.25" long with 56" teflon wires (brown). Cross: 117005 (A). Learn More

Heaters. Flexible thermofoil 24VDC 44 Ohm 150 Deg C. Mount: easy-to-install adhesive. Dimensions: 2.0 x 0.5" with 6" teflon wires (red). Polymide insulation. Learn More

Heater element 300 Watt 200V. Firerod. Dimensions: 3/8" OD x 1-5/8" long. Learn More

Heater. XRC3 230V 500 watt. INCOE� hot runner systems, pioneering the advancement of plastics processing in hot runner technology. Dimensions: 1.6 OD, 0.98" ID x 2" long. Orange and black teflon leads for heater, green for ground. Two iron/constantine T/C with red and white leads. Note: New older stock. Learn More

Heater. Heating element 115V 300watt. Firerod. Dimensions: 9.4mm (0.370" ) D x 37.1mm (1.464") long with 2 radial leads. Learn More

Heater coil. 240V 750 watt. Curved (36" overall) into a 7 x 3 x 3" space. Note: TI-38X982 0C-260-4981, asbestos covered leads. Learn More

Heating element, immersion. 120V 3000W. Mounting: top mouting plate 2-1/2"sq. Element is 10-1/2" long. Alt P/N 8-935, TG1303L. Learn More

HEATING ELEMENTS 120v boils water in less than 15 seconds USED IN "MR.COFFEE" RFE Learn More

Heating plate, 3 coffee cup size. 120VAC 120W. From a major coffee maker, triple warming circles about 3" diameter each. Thermostatic temperature control (Non-adjustable) and Power-On neon light. Size:10-3/8"L x 5-3/8" x 0.22" thick Pyrex glass. Learn More

ENGINE BLOCK HEATER - CSA LR-1843 Series-A 1500W 120-VAC 4.8"LOA Learn More

Cartridge heaters for plastic injection molding machines. Brass, 595watts, 220V. Case: 0.785" D x 15.00" long. Learn More

Heater. Element. Learn More

Heating elements. For: Allen Bradley Bulletin 709 N Series Thermal Heater Element for Sizes 0, 1 and 2 Motor Starters. Full Load Motor 9.69Amp. Learn More

Heater, element. 3 Wire. Dimensions: 0.63" D x 1.402" long, above mount. Overall length: 1.7" long. Note: Marked A1015-120V. Cat5494. 102052669. Learn More

Heater. Overload thermal unit heating element. Mark: C097A. Learn More

Size 1, Overload heaters 3.32-3.43Amp Learn More

Heaters. 230V 1100 watt. Dimensions: 1.5" OD x 7.75" long. Applications: used in plastic injection molds. Learn More

Heaters. XRC II, 230V 1400 watt. Dimensions: 2.5" OD x 10" long. Applications: used in plastic injection molds. Learn More

Heating element 1P 240V 2000 watt. DTID: SXV4931091D675. Military NSN 4520-01-527-4928. Learn More

Cartridge Heaters for Plastic Injection Molding Machines. Material: brass. 1000watts, 240V. Case: 0.785" D x 24.875" long. Learn More

Cartridge Heaters for Plastic Injection Molding Machines. Stainless steel, 1000watts, 240V. Case: 20mm D x 635mm long. Learn More

Cartridge Heaters for Plastic Injection Molding Machines. Stainless steel, 1025watts, 220V. Application: Used in injection molding machines. Case: 20mm D x 665mm long. Learn More

Cartridge Heaters for Plastic Injection Molding Machines. Stainless steel, 1200watts, 220V. Case: 0.785" D x 26.25" long. Learn More