Resistors

Resistor, ceramic. Resistance: 10 Ohm. Power: 1 watt. Tolerance: 5%. Technology: wirewound. Package: axial leads. Note: Enamel coated. Series 22. 

OHMITE - 0106 - Rheostat.

Resistance: 10 Ohm

Power: 12.5watt

Current: 1.1Amp.

Model E, Ceramic, 3-solder terminals.

Overall 22.3mm dia x 16.3mm tall with threaded 1/8" shaft.

Each is ind manuf bx's.

Ohmite - 20J10R  Resistor, ceramic. 10 Ohm.

Power: 10 watt.

Tolerance: 5%. Temp coef: 50ppm.

Technology: Wirewound. 

Package: axial leads. RoHS compliant. Series 20.

Package of 5.

Vishay Milwaukee Resistor Corporation - MRC 12/04 Resistor, Ceramic Brake Bracking.

Dynamic Braking Systems are used in applications such as: centrifuges, pumps, fans, certain conveyor belts, rapid/ continuous braking, and applications that require rapid slow down and reversing. The braking resistors market can be categorized into energy, oil & gas, mining, marine, automobile, and others.

Advantages - Dynamic braking resistors versus Friction braking

• Lower wear of components.

• Control motor voltage within safe levels.

• Faster braking of AC and DC motors.

• Less service required and higher reliability.

Resistance: 10 Ohm. Ribbed, Ribwound Enamel Coated.

Technology: Wirewound. 500 Watt

Ribbed construction aids in rapid cooling

Designed for equipment requiring low resistance
loads at low ohmic values and high current capacity.

Dimensions: 10-1/2" long x 1-3/4" D OD with 1-1/8" ID.

Color: Brown.

Global Model Number RBEF0500B

Alternate: Ohmite E500K10R

Used, As Removed

Proudly Made in USA

Milwaukee - 10N-030-602 Resistor, Ceramic.

10 Ohm.

Power: 100 Watt.

Technology: Wirewound.

Dimension: 6-1/2" x 7/8" D.

Enamel Coated. 

Alternates: 10N-030-602, L100J10RE, VK100N10, 12-104-10, RDEF0100

New Old Stock

Note: Milwaukee is now Vishay

Vishay DALE - NHL25-10R - Resistor, Ceramic.

Ayrton–Perry windings of resistance wire used to make wirewound RF resistors are used at high frequencies, where inductance and capacitance are unwanted.

The winding is made of two separate wires wound in opposing directions along an insulating form and connected in parallel at the ends. Since there are the same number of turns of wire in either direction, the magnetic fields of the two wires cancel each other out, so the coil has little inductance; and since adjacent turns of the two wires are at approximately the same voltage, there is little parasitic capacitance between the turns.

One disadvantage is that because the two lengths of resistive wire are connected in parallel, four times the length of wire (twice the length for each coil) is needed to make a given resistance, compared to when a single coil is used so they are more expensive than inductive wirewound resistors.

10 Ohm.

Power: 25 watt.

Tolerance: 5%.

Technology: Wirewound Non-Inductive with Ayrton-Perry Winding.

Dimension: 2.0"L x 0.7"D.

Weight: 1oz.

Genuine Dale - New Old Stock

Alternate: FST025-10-5%NI, FST02506E10R00JENI

MILWAUKEE - 100/10R NI Resistor, Ceramic.

A non-inductively wound resistor uses Ayrton-Perry winding technique which has one winding in one direction and one in the other. Since there are the same number of turns of wire in each direction, the magnetic fields of the two wires cancel each other to nullify inductance. One disadvantage of this technique is that it requires twice the length of coil to make given resistance as compared to standard winding. Ayrton-Perry windings are used in resistor to eliminate parasitic inductance at high frequencies.

Resistance: 10 Ohm.

Power: 100 watt.

Non-inductive Ayrton-Perry winding.

Dimensions: 3/4" OD x 6-1/2" long.

Fusible, Ceramic rod. Memcor and Milwaukee.

OHMITE - L12J12R Resistor, ceramic. 12 Ohm.

Power: 12 watt.

Tolerance: 5%.

Technology: wirewound.

Package: enamel coated, radial lug.

Note: ALT P/N: 270-12D-57 and 3756.

Additional Information: https://datasheet.octopart.com/L12J33R-Ohmite-datasheet-33006679.pdf