On Sale

Eaglerise Electric – Encapsulated Toroidal Transformer HLBB-140-0003 - B04202F1 – 140VA This toroidal transformer has heavier gauge wires than the normal requirement to avoid the copper lost during the full load output and over load output. Some advantages of toroidal transformers are higher efficiency, inherent EMI shielding, minimal signal distortion, more compact construction, low mechanical humming, low heat, and small off-load losses. Its disadvantages are more expensive construction, limitations on multi-phase systems, and higher inrush current. By reducing loss compared to EI transformers with fewer gaps and tighter windings, toroidal transformers have less vibration, or hum, that impact sound quality. Toroidal transformers are also designed to minimize core magnetization. Class B 130C Ta 35C UL CSA RoHS Multi-Coil Toroid Transformer Power Rating: 140VA Primary Winding Tapped at 115VAC and 230VAC 50/60Hz and dual secondary windings. Primary: Dual 120VAC primary (i.e. 120V/240V 50/60 Hz) 20 AWG Secondary: 24VAC and 28VAC secondary 5 Amp.16 AWG Double insulated Leads Flexible lead-out can be trimmed to any length without the need for removal of enamel Winding Max.Temp: 130C Diameter: 142mm, Inner Diameter: 30mm, Height 55.2mm Efficiency: 95 -99% Core: Ferrite Each transformer comes bagged with mounting hardware. Dished Mounting Plate, 2 Insulated Foam Pads, M8x1.25 Screw, Nut and Washer. Weight: 6 lbs Leads 300mm, 67mm Insulated Sleeving A toroidal transformer is a type of electrical transformer constructed with a torus or donut-shaped core. Its primary and secondary windings are wound across the entire surface of the torus core, separated by an insulating material. This configuration minimizes the magnetic flux leakage. Therefore, a toroidal core is regarded as the ideal transformer core design. Advantages of toroidal transformers are higher efficiency, inherent EMI shielding, minimal signal distortion, more compact construction, low mechanical humming, low heat, and small off-load losses. Toroid transformers have higher efficiency than other transformers, typically around 95 to 99%. This can be attributed to its near-ideal design, which perfectly contains the magnetic flux inside the windings. Thus, there is no leakage flux. Since the magnetic flux is highly concentrated inside the coil windings and the windings are evenly distributed to the whole toroid core, the magnetic flux is efficiently utilized to couple the primary and secondary windings. Toroidal transformers are suitable for sensitive and critical electronic circuits because of several advantages over traditional square and rectangular-shaped transformers. Some of these advantages are high efficiency, quiet operation, minimal heat generation, and compact size. They are mostly seen in power supply systems, audio systems, control equipment, power inverters, and other electronic devices. Applications: Toroidal inductors and transformers are used in a wide range of electronic circuits: Power Generation, Transmission & Distribution, Lighting, Audio Systems, Electronic Equipment, Power Supplies, Inverters, and Amplifiers, which in turn are used in the vast majority of electrical equipment: TVs, radios, computers, and audio systems. Note: Discounts provided for purchases of 2, 3, or 4 with "Make Offer" option limited to bulk purchases. Learn More

Meder Electronics - KSK-1A71/4-BV50822 - Switch, Magnetic Reed.

A reed switch is a passive device consisting of two Reed Blades sealed inside a glass tube with an Inert Gas, which operates when brought near a magnetic field.

The reeds are hermetically sealed in cantilever form so that their free ends overlap and are separated by a small air gap. The contact area of each blade can be coated with one of many types of contact materials such as Ruthenium, Rhodium, Tungsten, Silver, Irridium, Molybdenum etc.

Due to the low inertia of the Reed Blades and the small gap, fast operation is achieved. The inert gas inside the sealed Reed Switch not only prevents oxidation of the contact material but also helps in making it one of the few devices that can be used in explosive environments.

Note: Standex Electronics' reed switch-based solutions include Meder, Standex, and Kofu (formerly OKI) brand reed switches.

Status: Discontinued

Current Rating: 1Amp

Contact: Normally Open 1 Form A Contact

Case: Gass Envelope.

Dimensions: 0.1" Diameter x 0.625" Long.

New Old Stock

Learn More

Weidmuller - 5RL-750 - Transformer, Current. Ring Style

• Frequency 50-400 Hz

• Insulation Level 600 Volts 10 kV BIL full wave

• Window Diameter 1.56"

• Approximate weight of 1.0 lbs

Ratio: 75:5

50-400Hz 600V

INS. CLASS 10KV

Approvals: UL, CSA

Learn More

Weidmuller - 102450 - 1024500000 Terminal/Barrier Strip. Feed-Through 4 Position 

Allen Head, WM, BG265Amp 600V AWG:2 to MCM250.

Dimensions: 1.28 x 5.25 x 4.63"H.

Din Rail Mounting.

Approvals: UL CE 1.3 Lbs. WDU120

Made in Germany

Learn More

Weidmuller - 5784.6 - 0578460000 - Connectors, Terminal/Barrier Strips.

Stackable 1 Level 9 position.

Mount: Right Angle

Pitch:  5.0 mm (0.197")

Temperature: -50 C to 120 C

Connections: PCB Pins.

Made in Germany

Learn More

Weidmuller - 10200 WDU2.5 - Terminal/Barrier Strip.

Feed thru 800V 24Amp.

Number of Contacts: 2.

2P 1 Position.

Pitch spacing: 5mm.

For Wire Size 26-12AWG.

Terminal Type: Screw.

Mount: Din Rail.

Color: Beige.

Made in Germany

Learn More

Weidmuller - TS02-08 - Connector, Terminal Block.

Circuit Count: 2 Position.

Pitch: 5.0mm.

Insulation Voltage: 250V.

Mounting Type: PCB pins.

Outside Dimensions: 0.600" long x 0.5" wide (deep) x 0.753" high.

Snap together for additional lengths.

Right Angle.

Color: Orange.

Made in Germany

Learn More

Gould T48C407 - 16AWG Magnet Wire, Magnet. High Quality enameled Copper Wire! Durable and not break while winding the coils. Highly Efficient! Industrial Grade. 16 AWG-1C. (16 AWG AWG 1 Conductor). Conductor Type: Solid. Temerature: 200 C Cable Diameter: 0.050" Note: Enameled / Orange / Clear Varnished 100%. Applications: Construction of transformers, wound coils, motors, solenoids, instruments, inductors, speakers, electromagnets, and other applications that require tight coils of insulated wire. Package of 50 feet. Learn More

MODICON / AEG - AS-S902-171 - EXEC. I/O MODULE 984 Series PROM COMB.

1010 for Modicon Modbus Plus AS-S902-171.

New, in Bag.

Sealed Module has Gold Plated PC Card.

New - Made in USA

Learn More

ST Microelectronics - TIP42A - Transistor, PNP.

Max Voltage: 60V.

Max Ccurrent: 6Amp.

Dissipation: 65 watt case, 2 watt ambient.

Package: TO-220. P/N: TIP42A.

Note: Silicon.

Alternate: NTE197.

Learn More

Raychem - 202K163-3-0 - Tubing. Thermofit Heat Shrinkable Polymeric.

Molded Boot Straight Size 63.

ID Supplied: 1.692" (43mm)

Boot Color: Black

Length: 3.9" (99.1mm) 

ID Recovered: 1.11' (28.2mm) 

Type: PO Polyolefin

Shrink Ratio: 1.5:11O

 

Learn More

Lambda - LAS2705 - Voltage Regulator, Hybrid.

Polarity: Negative.

Adjustment range: -5V.

Current: 5Amp.

Tolerance: 5%.

Dissipation: 85 watt.

Case: Module.

Note: Used/Removed from Equipment. 

Learn More

Motorola - MC14078 - IC, CMOS.

8 Input NOR gate.

Package: 14 Dip.

Learn More

Analog Devices Inc - ADXRS300ABG - Angular Rate Sensor (Gyroscope) 32 Pin CSPBGA 300 deg./sec. angular rate sensor (gyroscope) on a single chip, complete with all of the required electronics. The sensor is built using Analog Devices' proprietary iMEMS surface micromachining process. Two polysilicon sensing structures each contain a dither frame which is electrostatically driven to resonance. A rotation about the z axis, normal to the plane of the chip, produces a Coriolis force which displaces the sensing structures perpendicular to the vibratory motion. This Coriolis motion is detected by a series of capacitive pickoff structures on the edges of the sensing structures. The resulting signal is amplified and demodulated to produce the rate signal output. 32-SMD Leadless Ceramin ball grid array.

Learn More

Capacitor, tantalum. 43uF 100V. Package; solid, axial leads. Dimensions: 9.6mm D x 20.0mm long. Note: May also be manufactured by ME. Learn More

KEMET - M39003/06-0172 - Capacitor, Tantalum.

Capacitance / Voltage Ratings: 47uF 35V.

Tolerance: 20%.

Package: Solid, axial leads, hermetically sealed case.

Dimensions: 7.3mm D x 17.0mm long.

Note: P/N T252C476M035PS7513.

Learn More

Honeywell/Microswitch - CRS301 - Color Recognition System.

Designed for the industrial environment, not just the laboratory bench. Accurately memorizes up to eight different colors for recognition on-line. Sensitive across the entire visible light spectrum 400 to 800 nanometers to characterize colors, not just red, blue & green. Internal light source. Current sink/source output provided for each channel.

400-800nM, 8-Channels.

Color Recognition Sensor with MS-Connector Cable

4 armoured 32" Fiber Optic cables: CRS-FO-25-3 (bifurcated CRS-FO-55-TSR-3, CRS-FO-55-TSE-3, and CRS-FO-55-3 (bifurcated).

3.5" Disk CRS 301-CFG-SFT V2.10 Software.

S/N 00058

New Old Stock - Made in USA - 9042

Learn More

TE CONNECTIVITY RAYCHEM - SAS-300-1-1030-0 - Thermofit Adhesive Sleeve, Meltable For Heat Shrink Tubing.

Raychem heat shrink tubing is available in different varieties of materials, colors and sizes. Each is designed to provide long term protection in the most demanding environments where moisture, corrosion, mechanical damage and extreme temperature are found.

Seal, Protect, and Strain-Relieve with Heat-Shrinkable Molded Parts in a Range of Shapes and Materials to Help Withstand Harsh Environments.

Molding temperature is 140°C (285°F).

Slit Adhesive Sleeve

Primary Product Color : Black

Primary Product Material : Polyolefin 

Extruded ID: 0.300" +/-0.005" (7.60mm)

Cut Length: 1.000" +/- 0.050"

Extruded Wall 0.060 +/- 0.003"

Alternates: CB5727-000, RPN 6984850001, 6984850001-SI

 

Learn More

Unidentified MFG - 285653-1 - Hardware, Knob.

For 1/4" Shaft with two Set Screws.

Beige with Directional Indicator.

Dimensions: 11/16" D x 3/4" High.

Note: Top Cap not Included.

Learn More

PTC - PTC7003 - Transistor, NPN.

Max Voltage: 500V.

Max Current: 50Amp.

Dissipation: 175 watt.

Package: TO-3 Steel Case, Gold Leads.

Note: Darlington.

New

Learn More

RAYCHEM TE Connectivity - 222D932-4 - 222D932-4-00/42 - Cable Boot & End Cap.

Seal, Protect, and Strain-Relieve with Heat-Shrinkable Molded Parts in a Range of Shapes and Materials to Help Withstand Harsh Environments.

Heat Shrink Boots, 90 °, Size 222, Lipped, 4, 10, -55 – 135 °C [-67 – 275 °F], Occasional Fluid Exposure

Molded Part Angle (°): 90

Molded Part Shape Code : 222

Lipped : Yes

Material Code : 4

Material: Flame-retardant, Flexible Polyolefin

Temperature Range: -55°C to +135°C

Heat Shrink Boot Material Systems Code : 10

Thermofit Molded Boot 90 degree with Lip

Place over product, heat evenly until the tubing or molded part shrinks into place.

Thermofit Heat Shrinkable Polymer.

Alternate: 808472-000, Newark 45M0482 

Learn More

PMI - OP15GZ - IC, Operational Amplifier.

Precision JFET-Input.

Type: Integrated Circuit FET

R(in) (Û): 1.0T-

I(io) Max. (A): 1.2n

V(io) Max. (V): 3.8m

PD Max. (W): 500m

Inp Bias Curr. Max. (A): 1.5n

Unity Gain BW (Hz): 5.4M-

Com Mode Inp Range (VICR): 10.2

Temp Coef. of VIO: 15u

Oper. Temp (°C) Min 0

Oper. Temp (°C) Max.: 70

Pinout Equivalence Number: 8-214

No. of Pins

High slew rate.

Bandwidth: 6MHz.

Package: 8 Cdip.

New Old Stock - Difficult Operational Amp[lifier to Find

Learn More

National Semiconductor Corp - ADC0832CCN - IC, A/D Converter.

8 Bit serial I/O with multiplexer options.

Alternate:/Equivalent: Analog Devices MAX131AEPL+

Package: 8 Dip.

Learn More

Logan Lundahl Instruments - DCU-A - 6-WIRE ULTRASONIC SENSORs with Adjustable Trip-point and Sensitivity.

The DCU series sensors use ultrasonic technology to provide a non-contact method of determining distance or level measurements.

Dimensions: 2" Square x 3.6" Long.

A Division of EZRA C LUNDHAL, INC 

Note: California-based Scientific Technologies Inc aquired Logan Lundahl Instruments.

New Old Stock - Made in USA

Learn More