Encoder

Synchro shaft angle data converter 10-Bit out Navy-MIL#2509543 21-Pin module with military spec's.Data Device Corp. 5998-010291519 Learn More

Electroswitch - OAK INDUSTRIES - LCE1N-2G09-36-3 Encoder, Rotary, 700 Series.

Electroswitch Electronic Products acquired OakGrigsby. 

Manual 2 Bit, 9-cycle, 36-Position with detents.

Gray code.

Housing material: Plastic, Gray.

Operating Temperature: -40C to 85C

Mount: Panel, Threaded-bushing.

Rotatiopn Life: 50,000 Cycles.

Max Operting Speed: 30 RPM

Dimensions: 0.890" (22.6mm) long x 0.830" (21.0 mm) wide plus 3 PC leads x 0.336" (8.5mm) high. Bushing length: (3/3-32), 6.3mm long. Shaft: 0.250" (6.35mm) D x 0.500" (12.7mm) long.

Note: Marked OAK 700. (0.830" x 0.343").700 encoder

Additional Information: https://www.electro-nc.com/oak/p0710.pdf

Learn More

Electroswitch OAK-GRIGSBY INC. - 94Q100-40-00 - Rotary Encoder.

The 900 Series offers a full line of low cost, rugged optical encoders with incremental output. Well suited for industrial motion and position sensing, their low profile and high resolution also make them ideal for panel mounted applications. A two-channel quadrature code allows the encoder to detect the direction and magnitude of the input motion applied to its shaft.

Optical. 100PPR, 3,000RPM max.

Two Channel Quadrature Output.

Style 2 Output: NC + A B.

Mount: Panel, 1/2" bushing and 1/4" SS shaft, ball bearing type, spins freely.

Package: Die Cast Housing, 1" Square.

Standard 4" 4-pin Ribbon Cable and Connector.

Note: Compact, Robust, Economical. 100 million+ operations.

 

Learn More

RESOLVER IN HEAVY DUTY MOUNT RATIO 6/1 SHAFT: 3/4" KEYED

Learn More

Encoder, rotary. Incremental 100-PPR. Bidirectional. Power requirements: current sink, TTL, TTL liner driver: 5 - 26VDC at 80mA max. plus load: CMOS line driver: 5 to 15VDC at 80mA max plus load. Output current: open collector: 40mA sink at 0.5V; line driver: 40mA source/sink. Environmentally sealed enclosure. Shaft: 3/8" single ended. 8830 TTL line driver. MS3102E-16S-1P, 7 pin male connector. Note: Qube. Complete with manufactures wiring instructions and guidelines.

Learn More

Rotary Optical Encoder. Incremental. Insta-Mount. Learn More

Optical Encoder Input-2000PPR Range:400,0006-1/8 " high x 5-1/4" dia. With one 32-Pin (M) panel mt military circular connector 3/8" dia shaft 1-1/8" long (Keyed) RFE-USED Make Us An Offer!!!! Learn More

BRUSHLESS AMPLIFIER by ELECTRO-CRAFT 5'x3"X2.3"ADJUSTABLE LOOP GAIN, CURRENT LIMIT VCS GAIN AND TEST/OFFSET.+/- 10V 5mA OUTPUT +5V@30mA OUTPUT Learn More

DISC INSTRUMENTS - Honeywell - PC62D-40-5 OPTICAL ENCODER

Made in USA

Used / As removed from Equipment

Learn More

Encoder, rotary. 1200PPR. Double ended 1/2" shaft. Dimensions: 3.5" round. Overall 4-1/3" long x 3.5" wide x 4-1/4" high (including shaft). Plus one male military circular connector P/N: MS3102E14S-6P. New. MFG CD: C592907 0007. Date code: 9826. Learn More

Danaher Controls – Dynapar - HA62509000101 - Encoder 3/8 SHT FLG MT 5-26VDC SD MT- New Description The Series HA25 is a rugged and reliable encoder for industrial motion applications. The proven design can be the mainstay for any automation project. Mechanical / Electrical Attributes Shaft / Bore Size (mm): 9.525 Connection Location: Radial Disk Material: Glass Flange Material: Aluminum Maximum Operating Speed (RPM): 6000 Connection Type: Connector Termination: 7 Pin MS Connector Shaft Type: Shafted Shaft / Bore Material: Stainless Steel Resolution (PPR): 900 Line Driver Type: 7273 Output Signal: Open Collector w/ 2.2K Ohm Input Voltage: 5-26 VDC Incremental Signal Format: Format A: A Leads B CCW; Index Width (180°) Gated to B' Reverse Polarity Protection: Yes Duty Cycle: 45-55% Short Circuit Protection: Yes Maximum Frequency Response (KHz): 100 Incremental Signals: A Environmental Attributes: Hazardous Area Rating Certification {[None] Minimum Storage Temperature (°C): -40 Noise Immunity Testing Specification: EN61326-1 Hazardous Area Rating: {hazardous_area_rating_certification=[None] Shock Resistance: 50G Humidity Non-Condensing (%): 98 Minimum Operating Temperature (°C): 0 Vibration Resistance: 20G Housing Protection Level: IP66 Maximum Operating Temperature (°C): 70 Maximum Storage Temperature (°C): 90 ROTARY ENCODER 3/8 SHT FLG MT 5-26VDC SD MT DYNAPAR HA62509000101 / HA62509000101, Factory New, INCREMENTAL ENCODER, SHAFTED ENCODER, SERIES HA25, SIZE 25 ENCLOSED, WITH SHAFT SEAL, GLASS DISK, 0900 PPR, FLANGE MOUNT, 3/8" SHAFT, 7 PIN MS CONNECTOR OR CABLE, SINGLE END, W INDEX, 5-26V IN, 5-26V OC W 2.2 KOHM PULLUP OUT, SIDE MOUNT CONNECTOR Made in USA Learn More

Optical Encoder for hazardous locations 72mmD. 95mm flange-mount. Double-flatted 0.38" Shaft. Listed UL CUS 56G5. Telemetering Equipment. NEMA 4X and 6. 0-70C Input:5-28VDC 4VA. BEI INDUSTRIAL ENCODER DIVISION H38D-400-AB-7273-SC-UL Learn More

Express Incremental Rotary encoder. S35F-62-R1-SS-1000-ABZC-7272-SM18 0.625" hollow shaft 1000Cycles/Rev. Electrical: Output: Two chnnels in quadrature. 1,000 cycles/turn. Supply: 5-28VDC 100mA. Complementary outputs. Reverse, overvoltage and short circuit protection. MS-connector. Mech: Shaft Bore: 0.625", with insulating sleeves. Tether Block and pin. Bore Runout: 0.001" T.I.R maximum. Bearings: 52100 SAE High carbon steel. Bearing Housing: Die cast aluminum with protective finish. Cover: Die cast aluminum with protective finish. Bearing Life: 7.5 X 109 revs (50,000 hrs at 2500 RPM) Maximum RPM: 6,000 RPM. Moment of Inertia: 0.019 oz-in-sec2. NEMA 4 & 13 IP65. Weight: 18 oz.

Learn More

Optical Incremental Encoder. Series A. 5VDC 500 CPT. With attached Cannon 10 Pin male circular connector MS3102E18-1P. Complete with manufactures instruction manual. Made in the USA. Learn More

Encoder, optical incremental. 1024 Resolution. 24VDC in, 5VDC DLD out. Channel A, B and Z. Series A. Mount: square flange. Shaft: 3/8" D. With a CA3102R18-1P 10 Pin flange male connector and mate CA06R18-1S 10 Pos female cable mount. Note: ALT P/N 98301075. Complete with manufactures installation instructions. Made in the USA. Learn More

Optical Incremental Encoder. Diemsnsions: 64mm with a shaft 9.5mm. Has a 10 Pin MS3102E18-1P male connector. Mount: 3 hole, 42mm apart. Overall: 91mm tall including shaft. Learn More

Encoder, Rotary. 3600-Pulse/Rev 12VDC. 122mmD x 140mmL with 0.6"[15mm] flatted shaft 1''Long. 5-Inch [127mm] Flange mount. Learn More

Rotary shaft encoder. Learn More

Sealed linear encoder. 240mm. Measuring standard - DIADUR phase grating on steel. Output signal - 1 Vpp. Signal period - 4 �m. Accuracy grades - � 3�m. Single-field scanning 1 VPP; 20 um. Recommended measuring steps - to 0.1 �m. Thermal behavior similar to steel or cast iron. High vibration rating. For incremental linear measurement with very high repeatability. Measuring length - 240mm. Reference mark - One or distance-coded High positioning accuracy through single-field scanning. Horizontal mounting possible. Learn More

Encoder. Marked: Resocoder. Mount: Panel, mount plate 2.654" square with 4 holes at 2.85" centers. Dimensions: body 2.5" D x 3.42" long, plus shaft, mount flange and connector. Shaft: 0.38" D x 0.846" long. Has one 10 Position male circular connector, part number MS3102E18-1P. Used/Removed from equipment. Overall length of unit is 5.75". Note: No other information available. Learn More

Encoders, rotary. Supply: 12VDC 150mA. Tolerance: 5%. 3600P/R 2 phase square wave + zero mark. Totem pole output, load resistance 470 Ohm min. Open collector output 40 VDC, 50mA or less. Timing can be selectable. More info: PG8 http://www.onosokki.co.jp/English/hp_e/whats_new/Catalog/PDF/RPseriesE.pdf

Learn More

Waters International Manufacturing Inc - APT55-11-B - Encoder, Rotary.

Encoder, Rotary.

Position Transducer.

Absolute Potentiometric Encoder.

Resistance: 10K Ohm.

Tolerance: 10%.

Shaft Angle 360 Deg.

Dimensions: 2.171" D x 1.786" high.

Made in the USA.

New Old Stock

Learn More

Shaft Angle Encoder 4.7mm round shaft ~ 27mm diameter, has long cable with MS connector. Learn More

Encoder, rotary. Incremental 600-PPR. Unidirectional. Power requirements: current sink: 5 - 26VDC at 100mA max. plus load: line driver: 5 to 15VDC at 200mA max plus load. Output current: open collector: 40mA sink at 0.5V; line driver: 40mA source/sink. Environmentally sealed enclosure. Shaft: 3/8" single ended. 7406 Open collector with 2.2k pull-up. MS3102E-14S-6P, 6 pin male connector. Note: Qube. Complete with manufactures wiring instructions and guidelines.

Learn More