Microphones

BE-010 Microphone Windscreens

On stage or in a recording studio, a microphone is the most important device you need to capture vocals and instruments. Whether you're cutting your hit single or rocking out in front of a large crowd, your microphone projects everything you do, so having good quality mic accessories just makes sense. Windscreens and grilles are small, lightweight and portable components that can really impact the sound of your performance. Windscreen and grilles are covers that improve the sound quality of a microphone. Normally a windscreen is made from foam and a grille from metal. They act as a filter to prevent popping, breath sound, moisture and wind noise from reaching your mic.

Dimensions: 1-5/8" tall with a 7/16" Diameter Opening and an Inside Depth 1-1/3"

High Quality Multi Foam is ideal for reducing wind, sibilance and pop noise. 

Slides on Easily.

(Available in Black or Brown)

Learn More

PRIMO - EM-47A Audio, Microphone.

From live concert sound to recording a movie, pro-audio microphones are critical to the clarity of the sound. Primo's products are use inside many major brands from vocal mics to shotgun camera mics, our quality is perfect for professional and amateurs alike.

Electric Condenser Microphone Cartridge.

Omni-directional.

Highest quality, very high output into 200Meg Ohm to 500Meg Ohm, using FET AMP with source follower.

Has no internal preamps.

Can withstand very high S.P.L. (sound pressure level over 90db?).

Dimensions: 0.828" (21mm) D x 10.5mm high.

Threaded.

Learn More

PANASONIC WM-034CY - WM-034 - Audio, Microphone Cartridge.

Omnidirectional Electret Condenser Cartridge.

Part Status : Discontinued

Electret Condenser, Omnidirectional 42db +/-3db.

Frequency Range: 20Hz to 16kHz.

Impedance: 2.2K Ohm. (2200 Ohms)

Sensitivity: -62+/- 3dB

Signal Noise Ratial: 60 dB

Voltage: 4.5VDC, Voltage Range: 4.5 to 10V  (Vs)

Current: 800uA.

Output Type: Analog.

Dimensions: Circular 9.7mm Diameter x 6.7mm thick. (0.382" X 0.264")

Through hole Radial PCB mount, 2.54mm (0.100") standard pin spacing.

Termination: Solder Pads.

Applications: Useful for almost any type telephone and other applications.

Alternates: P9992-ND, CTI 42059, YPM-CH022, V79CH

Made in Japan

Learn More

ASTATIC - T2M-914 Replacement Omnidirectional Audio, Microphone /Speaker.

Speaker / Microphone Matches Virtually any Transmitter.

Micro Switch with Positive Snap Action.

Rotable Spring Clip on Back.

Power Requirements: 3 to 12 VDC.  

Quality Electret Cartridge. 

Lightweight Durable Noryl Housing.

Dimensions: Approximately 2" wide x 3" high x 1.3" D.

Complete with 6 wire Neoprene coil cord, extends to 5-1/2 feet. 

Includes Hook-up Instructions. 

Electret microphones are a type of electrostatic capacitor-based microphone which eliminates the need for a polarizing power supply by using a permanently charged material.

Proudly Made in USA

 

Learn More

Astatic FV272 - 1740 - Audio, Microphone Element, Dynamic. Astatic microphones are engineered to surpass all stock mic options, providing superior sound quality for CB, Amateur, and Single Side Band communications. Element Miniature. Dimensions: Approximately .750" X .50" X .36" (19.5 X 12.7 X 9.0 mm) Strong on Higher Frequencies. Researching this element to confirm if it is the Heil HC-5 or replacement that is in high in demand by Ham Radio Enthusiasts. Purchased from Astatic following their Conneaut Ohio plant closure. Made in Taiwan New Old Stock - 1980s Vintage Learn More

DM60 Audio. Microphone Cartridge.

400 Ohm Coil.

Material: Nylon Case.

Dimensions: 0.985" OD x 0.8" Length.

Color: Beige.

Purchased from Astatic Factory following Shutdown. Over 200 Sold.

Vintage New Old Stock

Learn More

CTI Audio 05114 Audio, Microphone Elements.

Approximate dimensions: 0.553" OD x 0.838" high.

No other information available.

Learn More

Computer Related. USB-A to USB-B Cable.

• Burst data transfer rates up to 480 Mbps (system dependent)
• Compliance with the USB 2.0 serial bus interface standard
• Backward compatibility with all USB 1.1 interfaces

Standard USB Male to Male Cable.

Length: 6 Foot.

Color: Beige.

Temperature: 60 C

High Speed Transfer:  Up to 480 Mbps transfers data speed for USB 2.0 devices

Backwards compliant with USB 1.1 (12 Mbps) and low-speed USB 1.0 (1.5 Mbps).

Cable Specifications: 2835 E87647-DG AWM 60 Deg C 30V VW1.

UL Approved

New Old Stock

Applications: This cable is designed to interconnect devices with USB interfaces. Ideal for connecting an audio interface, Printer, Scanner, Server, Fax, camera, piano, USB microphone or instrument, and many other peripherals to a PC. 

Learn More

Switchcraft - M3M XLR Audio Connector.

Male with shell having 13/16-27 external threads to engage equipment with internally threaded body. Terminals extend out rear (threaded end) to permit wiring without disassembly. Adapter receptacles mount directly to microphones or similar equipment to provide highly reliable 3-, 4- and 5-pin Switchcraft Q-G® connections. Adapter shell and coupling nut are brass, satin nickel finish.

Standard: Standard XLR

Housing Material: Brass with Satin Nickel Plated Finish

Gender: Male

Number of Contacts: 3, Number of Ports: 1, Number of Positions: 3

Dimensions: Length 27.79 mm

Male 3 Pin Microphone Adapter Receptacle.

Polarizing Groove & .25 Keyway

Overall Dimensions: .813" Long X .734" Diameter (20.65 X 18.64 mm)

13/16 - 27 UNS-2A Thread

Applications: Automotive, Communications Equipment, Enterprise Systems

Mouser P/N 502-M3M

Learn More

RCA Tac Tec Astatic - M1569029 Microphone.

Replacement Microphone for RCA Tac Tec 2-Way Radio Receivers. (Spec1476A).

Retractable Coiled Cord

7 Position Female Connector.

Spec. 1476A

Rare - New Old Stock - Vintage collectable

Made in Japan

Learn More

Belkin - 75-210B - Coiled 6.35mm (1/4") Male/Female Stereo Audio Headphone Extension Cord.

Cable: Quality TRS Male Stereo to Female Jack Extension, Shielded Stretch Cord.

Connectors: 6;35mm Male to 6.35mm Female

Molded Strain Reliefs

Conductor Material: Copper

Length: 5 foot Coiled extends to approximately 14 Feet

Applications: Headphone or ear bud extension and remore location for easier connectivity to other equipment.

Learn More

Microphone Replacement Grille Ball Head Mesh Cover, Windscreen.

If you’ve ever spoken into a microphone before, you probably know to speak into the metal grille for the best results. Chanced are you’ve spoken into a handheld microphone with a spherical grille. Microphone grilles come in many shapes and sizes and have many purposes for microphone performance!

The windscreen attenuates wind noise and environment noise and provides ample protection.

Material: Metal, Heavy Screen.

Fits Many Brand Mic Accs

Audio, Microphone.

Head/Cover only with windscreen.

Dimensions: overall 1.734" D x 2.860" high.

Black lower 1/2 is actually 0.920" Long, Windscreen is actually 1.927" long.

Threaded ID 1.244" (31.6mm) Diameter at base.

Learn More

Astatic - ASC650 - Audio, Microphone. Housing and Head Cover Headcase w/Windscreen. The Astatic - ASC650 is a high-quality microphone Housing designed for live performance, featuring a unidirectional polar pattern to increase vocal articulation and maximize rear rejection. With a sleek black design and wireless connectivity, this microphone is perfect for musicians and performers looking for top-notch audio equipment. Made in the United States by Astatic, the ASC650 comes with a housing head cover and windscreen to ensure clear and professional sound quality. Ideal for those seeking a reliable and versatile microphone for their live performances. The Astatic Corporation has been a leader in audio reproduction since 1930, known for microphones, phonograph cartridges, and needles. The Astatic ASC650 is used in situations where a microphone's head, cover, and windscreen need to be replaced or where a microphone assembly is being built or repaired. Audio, Microphone Housing and Head Cover Windscreen without Capsule. Body/Casing: Encloses the internal components and provides a housing for the microphone. A Rugged Metal Housing suitable for live performance and on-stage use. Designed to increase vocal articulation, maximize rear rejection, and lower handling noise Mounting: Threaded mounting ring assembly for adapting handheld transmitter body. Color: Black with Black Microphone Mesh Polar Pattern: Unidirectional Dimensions: Overall 1.419" Diameter (At Widest) x 2.375" High. Lower 1/2 portion is actually 1.288" Long, Windscreen portion is actually 1.120" Long. Threaded ID 0.87 " (22.1mm) Diameter at base. Applications: Unable to identify specific Model applications. Use above dimensions to determine compatibility. Purchased directly from the Astatic following the closure of the Conneaut, Ohio Manufacturing facility. Genuine Astatic – Vintage – Difficult part to find New Old Stock Made in USA Learn More

Audio, microphone cartridge.

Open frame.

Dimensions: Approximately 1.147" x 2.406" high.

 

Learn More

Waterproof microphone 2500-Ohm 2 wire termination sensitivity -54 dB +/- 3 dB TINY 5.5mm LONG x 4.5mm DEEP x 2.2mm THICK Learn More

Audio, speaker. CB Series miniature speaker, Z=24 ohm. Port on face, can function as a microphone or beeper. Enclosed, stainless steel. Mount: PCB. Dimensions: square 25.15mm long x 25.15mm wide x 9.65mm high. Very Nice. Learn More

UnBranded - 8-603 - Audio, Microphone/Speaker for Two Way Radio Walkier Talkie.

Hand Held with Locking Slide Switch Press On-up to Talk

Connectivity: Two Male 2-Conductor Plugs about 5/8" apart, one 2.5mm and one 3.5mm.

Approximate Dimensions: 5.25" high x 1.5" wide.

Color: Light Green

Type of Jack: K 

Vintage - New Old Stock

Made in Japan

Applications: Compatible with various K-Head walkie-talkies

Learn More

Microphone Element for Telephones.

Dimensions: 1.257" D x 0.180" High.

Overall 0.412" Deep.

Note: Each with a clear plastic protective cover, overall 1.539" D x 0.37" deep, with threaded ID.

Learn More

Microphone Windscreens approx L 1-5/8" x W 1-1/8" ,1/2" Hole for inserting microphone.Hole is 1-3/8" deep Natural color New Bulk packed. Learn More

CTI - 41821 - Miniature Microphone Elements

Felt Top

Dimensions: 10.6mm tall x 10.0mm Diameter.

3-Radial Leads on Bottom of Element.

Aluminum Shell

Learn More

Unidentified MFG - 6-158 - Audio, Microphone Element. Crystal, Piezoelectric, New Vintage Vintage Microphone Element - 6-158 - Audio, Microphone Element. Crystal, Piezoelectric Piezoelectric Microphones, also called Crystal Microphones, were used primarily between 1930 and 1960. At the time, these were important to the home recording and small-scale paging market, but were later replaced by lower-cost dynamic and electret capacitor microphones. Capacitive Nature: A crystal microphone functions like a capacitor, generating a voltage when subjected to sound pressure (piezoelectric effect). While capacitors allow current to flow when charging and discharging in an AC circuit, the inherent insulating property of the crystal itself presents a very high impedance to a direct current measurement from an Ohmmeter. Crystal microphones rely on the piezoelectric effect: This means they generate a voltage when mechanically stressed, like when sound waves cause their diaphragm (attached to the crystal) to vibrate. Type: Audio, Microphone. Crystal, Piezo High Z. (Will Measure Open using an Ohm meter, approximately 260 pF) Blue Plastic Body. Overall Dimensions: 22.7mm Diameter, Round x 11.1mm High. (0.875” x 0.437”) New Old Stock Vintage – Difficult Microphone Elements to find. Manufactured in Taiwan Applications: Great for radio and electronic project experimenter use, vacuum tube circuits, anywhere a high impedance microphone is required. Home recording systems, Amateur communication, Mobile communication. Piezoelectric crystals are durable and have a relatively large electrical output; for this reason, they were often used in telephones and portable sound systems. They do not have very good linearity and so are inadequate for quality high fidelity sound recording. Discounts provided for Lot purchases of 2, 3, or 4 with the Make Offer” option limited to bulk purchases. Learn More

Audio, microphone. Cartridge, sensitivity -63(+/-)3dB. Dimensions: 10mm OD x 9mm. Learn More

Close-talking electret microphone - 2500 Ohm - 2 wire termination - sensitivity -52 dB +/- 3 dB Learn More

CTI AUDIO INC / Omnitronics - 41543-03-00 - Microphone Square Grille Mesh Cover Replacement, Audio, Microphones. Windscreen. The CTI Audio Inc / Omnitronics 41543-03-00 Microphone Square Grille Mesh Cover is a lightweight accessory designed to cover the microphone. With a weight of 2.88 ounces, this square grille mesh cover is durable and reliable for use in various musical instruments and gear. The brand CTI Audio / Omnitronics ensures quality and compatibility with the product. The sleek design and mesh cover provide a stylish and functional addition to any microphone setup, enhancing both the sound quality and aesthetic appeal. CTI Audio, Inc. is the previous name formerly related to Astatic/ Omnitronics and today known as CTI (Custom Technology Integration), and which provides audio-visual and event production services. Audio, Microphone Grille Manufactured by Millcreek Metal Finishing, Erie PA.. Rugged double mesh grill for high RF immunity but unaffected acoustics. Grille Material: Steel Mesh Windscreen Dimensions: 1.75" square. Professional Vintage - New Old Stock - Genuine CTI / Omnitronics Microphone Grille - Rare Proudly Made in USA Learn More