Featured Products

Unidentified MFG - 4243000 - Connector, Coaxial.

Type: BNC.

Housing Gender: Receptacle.

Contact Gender: Female.

Connection: Inline Cable End for RG-58.

Note: 3 Parts/per unit.

Learn More

RF Industries - RSB-4050-B - SMB Connectors, RF. RG174 & LMR-100

An SMB connector is a coaxial RF connector with a snap-on connection. SMB connectors are smaller than SMA connectors and are primarily used in telecommunications and automotive applications. 

Description: SMB 50 OHM JACK CRIMP, N,G,T; FOR RG-174/U & RG-316/U, CBL GRP B

• Fits RG74/U RG-316/U & LMR-100
• Crimp style
• 50 ohm
• Nickel Plated Brass

SMB (Sub-Miniature Version B) Male Pin for 0.063"D Teflon RG178B/U Coaxial Cable.

Type: Crimp Style

Connector Gender: Female with Gold Pin Contact

Body Style: Straight

Impedance: 50 Ohm

Working Voltage: 400 VRMS (375V peak)

Frequency Range: 0-12.4 GHz, Excellent Electrical Performance from DC to 4 GHz.

Mounting Type: Free Hanging (In-Line)

Contact/Shield Termination: Crimp

Dielectric: Teflon

Contact: Gold Plated Pin

Fastening Type: Snap-On

Cable Group: B

Set of: Gold-Plated Pin, Crimp Ferrule and Housing.

Alternates: Digi-Key 2737-RSB-4050-B-ND, UPC 729198767174

Applications: The SMB connector is used in applications where a quick mating sub-miniature RF connector is required for RF frequencies up to frequencies of a few GHz. The SMB connector derives its name as it is termed a Sub-Miniature version B connector.

Made in Taiwan

Factory New

Learn More

Diode, zener. Voltage: 7.5V. Power: 5 watt. Tolerance: 5%. Package: axial leads. Learn More

 C45627D - Dual MV/ TC Printed Circuit Board.

Amplifier PCB for Sensor: 44018.

Range: 0-100 C.

Output: 0-10VDC.

Power: 115VAC.

Dual MV/TC.

Dimensions: 4" x 6.5" with 12-pin Edge card plug.

Learn More

Crystal. 16.625MHz. Package HC49UA metal can. Note: Cordless phone crystals. Package of 12. Learn More

Coupler, bi-directional. Incident: Frequency MC: 400, 425, 450MHz. Coupling DB: 40.5, 40.0, 39.5 Reflected: all the same as Incident. Dimensions: 11'' long with two Prodelin 521-835(2) 5'' Flange-to-''N'' Adapters approximately 10'' long each. Project: SPS-40. Military 97942-1A20305H01. Learn More

Cartridge Heaters for Plastic Injection Molding Machines. Brass, 880watts, 240VAC. Resistance: 65 Ohm. Rod Heater. Case: 20mm D x 890mm (35.5") long. Fiberglass leads, about 10" long. Weight: 1.93 lb. Learn More

Cable assemblies. Shielded with a molded RA silver plated RCA connector on one end. Length: 18 inch. Learn More

SCR, silicon controlled rectifier. Voltage: 600V. Average on state current: 16Amp. On state RMS current: 25Amp. Package: TO-220. Learn More

1N2069  Diode. 200V 0.75Amp Silicon Rectifier.

Case: DO-41 axial leads.

Tarnished leads - More difficult Diode to find.

New Older Stock. 

Learn More

Cartridge Heaters for Plastic Injection Molding Machines. Brass, 680watts, 220V. Case: 0.785" D x 19.25" long. Learn More

Cartridge Heaters for Plastic Injection Molding Machines. Brass, 680watts, 220V. Case: 0.785" D x 15.00" long. Learn More

Cartridge Heaters for Plastic Injection Molding Machines. Brass, 640watts, 240V. Case: 0.785" D x 17.25" long. Learn More

Cartridge Heaters for Plastic Injection Molding Machines. Brass, 600watts, 440V. Case: 0.785" D x 19.875" long. Learn More

Cartridge Heaters for Plastic Injection Molding Machines. Stainless steel, 600watts, 240V. Case: 0.785" D x 17.25" long. Learn More

Cartridge Heaters for Plastic Injection Molding Machines. Brass, 600watts, 220V. Case: 0.785" D x 19.875" long. Learn More

Cartridge Heaters for Plastic Injection Molding Machines. Brass, 595watts, 260V. Case: 0.785" D x 14.75" long. Learn More

Cartridge Heaters for Plastic Injection Molding Machines. Brass, 470watts, 240V. Case: 0.785" D x 15.75" long. Learn More

Hardware, washers. Spacers/Insulators. Material: nylon. Dimensions: 0.750" (19mm) OD x 0.119" (3mm) wide x 0.010" thick with 0.520" (13.2mm) ID. Package of 1,000. Learn More

245537-25 Connector, D-Sub.

Male DB25.

Contacts: Gold Plated

Mount: Panel/chassis.

Termination: Solder.

Alternate: Amphenol L717DB25P

Learn More

Cartridge Heaters for Plastic Injection Molding Machines. Stainless steel, 1360watts, 240V. Case: 0.785" D x 23.125" long. Learn More

Cartridge Heaters for Plastic Injection Molding Machines. Brass, 1200watts, 240V. Case: 0.785" D x 26.125" long. Learn More

Cartridge Heaters for Plastic Injection Molding Machines. Stainless steel, 1200watts, 220V. Case: 20mm D x 670mm long. Learn More

Cartridge Heaters for Plastic Injection Molding Machines. Stainless steel, 1200watts, 220V. Case: 20mm D x 620mm long. Learn More