Other Process Control

SKAN-A-MATIC - S28002 - Photoelectric, Sensor / Wafer PhotoDetector Sensor. New

The S28 series skanner is a specially constructed LED Sensor designed to detect wafers for the semiconductor industry. polished and unpolished wafers can be detected from the same sensing point.

Operating Voltage: 30 VDC Max.

Spectra Response: 910 nm peak, filtered to respond to less than 5% at 750 nm and less than 0.1% at 700nm.

4 Conductor, 26 GA, Teflon Covered Cable with shielded photodetector leads and overall shield.

LED Skanner

Operating Distance 0.050".

Bottom Mounted Cable.

Note: LED must be current limited, 40mA max which will result in a forward voltage drop of 1.0-1.6VDC.

New Old Stock in Manufacturer's Packaging

Learn More

Photoelectric, sensor. Learn More

Clarostat Honeywell Scan-O-Matic T22029 - Logic Card / Board

The Logic Card is a required component for each control. Since some functions use only one output, it is wise to select the desired card before ordering the Chassis.

AND/NAND—OR/NOR Logic w/One Shot

Logic Board

New Old Stock

Learn More

Clarostat Honeywell SKAN-A-MATIC - T21011 -  Photoelectric Amplifier Scanner Control Module

The T21011 photoelectric amplifier module is designed to amplifieroutput from a photodetector. The output of the photodetector is taken as the input of the module.

Status: Discontinued

Features:
■ Modular approach
■ Printed circuit board mounting
■ Low power consumption
■ Small size
■ Gold plated leads
■ Epoxy encapsulated

With Adjustment and LED Indicator

Mount: PCB 

Connections: 5 Square Pins

New Old Stock

Made in the UK

Learn More

Clarostat Honeywell SKAN-A-MATIC - T21010 -  Photoelectric Amplifier Scanner Control Module

The T21010 photoelectric amplifier module is designed to amplifieroutput from a photodetector. The output of the photodetector is taken as the input of the module.

Status: Discontinued

Features:
■ Modular approach
■ Printed circuit board mounting
■ Low power consumption
■ Small size
■ Gold plated leads
■ Epoxy encapsulated

Mount: PCB 

Module with LED & Trimpot.

Connections: 5 Square Pins

New Old Stock

Made in the UK

 

Learn More

Clarostat Honeywell SKAN-A-MATIC - T21009 -  Photoelectric Amplifier Scanner Control Module

The T21009 photoelectric amplifier module is designed to amplifieroutput from a photodetector. The output of the photodetector is taken as the input of the module.

Status: Discontinued

Features:
■ Modular approach
■ Printed circuit board mounting
■ Low power consumption
■ Small size
■ Gold plated leads
■ Epoxy encapsulated

Mount: PCB 

Connections: 9 Square Pins

New Old Stock

Made in the UK

 

Learn More

Clarostat Honeywell SKAN-A-MATIC - T21008 -  Photoelectric Amplifier Scanner Control Module

The T21008 photoelectric amplifier module is designed to amplifieroutput from a photodetector. The output of the photodetector is taken as the input of the module.

Status: Discontinued

Features:
■ Modular approach
■ Printed circuit board mounting
■ Low power consumption
■ Small size
■ Gold plated leads
■ Epoxy encapsulated

Mount: PCB 

Connections: 10 Square Pins

New Old Stock

Made in the UK

 

Learn More

Clarostat Honeywell SKAN-A-MATIC - T21007 -  Photoelectric Amplifier Scanner Control Module

The T21007 photoelectric amplifier module is designed to amplifieroutput from a photodetector. The output of the photodetector is taken as the input of the module.

Status: Discontinued

Features:
■ Modular approach
■ Printed circuit board mounting
■ Low power consumption
■ Small size
■ Gold plated leads
■ Epoxy encapsulated

Mount: PCB 

Connections: 10 Square Pins

New Old Stock

Made in the UK

Learn More

Clarostat Honeywell SKAN-A-MATIC - T21006 -  Photoelectric Amplifier Scanner Control Module

The T21004 photoelectric amplifier module is designed to amplifieroutput from a photodetector. The output of the photodetector is taken as the input of the module.

Status: Discontinued

Features:
■ Modular approac h
■ Printed circuit board mounting
■ Low power consumption
■ Small size
■ Gold plated leads
■ Epoxy encapsulated

Mount: PCB 

Connections: 8 Square Pins

New Old Stock

Made in the UK

Learn More

SKAN-A-MATIC - T20126 - SCANNER CONTROL MODULE

Learn More

Selector auto step unit. Rear connectors: Inlet, Outlet, Machine I/O, Out and Gage Head. Has various LED displays on front of box. With a few attached cables: Inlet, Out and I/O. Learn More

SICK OPTIC ELECTRONIC - WT12-N1421 – Photoelectric Proximity Switch, New The SICK WT12-N1421 (Part No. 1010807) is a photoelectric proximity sensor designed for non-contact object detection. As part of the SICK W12 series, it features a rugged metal housing suitable for demanding industrial environments. Core Specifications • Sensing Range: Adjustable from 35 mm to 100 mm. • Output Type: NPN digital output. • Supply Voltage: 10 V DC to 30 V DC. • Output Current: Maximum of 100 mA. • Connection: Pre-wired with a 4-wire cable, typically 1.5 to 2 meters in length. • Adjustment: Features a manual potentiometer for fine-tuning the sensing distance. Physical & Environmental • Housing Material: Durable zinc die-cast metal. • Dimensions: Approximately 15 mm x 49 mm x 41.5 mm (standard W12 rectangular form factor). • Protection Rating: Often rated up to IP69K, providing high resistance to water and dust. • Operating Temperature: Reliable performance from –40 °C to +60 °C. This sensor is commonly used in packaging, automotive, and logistics applications due to its ability to handle optical interference and harsh physical conditions. Factory New Learn More

SICK OPTIC ELECTRONIC - WT2000-B5320 - Photoelectric sensor. Energetic proximity sensor. New Functional principle Photoelectric retro-reflective sensor Housing design (light emission) Rectangular Sensing range max.: 0 m ... 15 m 1) Sensing range: 0 m ... 15 m 1) Focus Approx.: 1.3° Type of light: Visible red light Light source: LED 2) Light spot size (distance): Ø 320 mm (14 m) Angle of dispersion: Approx. 1.3° Wave length: 660 nm Adjustment Potentiometer Supply voltage: 10 V DC ... 30 V DC 1) Ripple : 5 V 2) Current consumption: 80 mA 3) Switching output: PNP /NPN Output function: Complementary Switching mode: Light/dark switching Switching mode: selector Selectable via light/dark selector Signal voltage: PNP HIGH/LOW Approx. VS – 2.0 V / 0 V Output current: Imax. ≤ 100 mA Response time: ≤ 1 ms 4) Switching frequency: 500 Hz 5) Time functions Off delay: 6) On delay 7) Delay time ≤ 0 ms,≤ 5 ms, ≤ 10 ms, ≤ 20 ms, ≤ 50 ms Connection type Male connector M12, 5-pin Circuit protection A 8) C 9) D 10) Protection class II : 11) Weight: 150 g Polarisation filter ✔ Alarm output: PNP Housing material Plastic, Glassfibre reinforced plastic Enclosure rating: IP67 Ambient operating temperature: –25 °C ... +40 °C Ambient temperature, storage: –40 °C ... +70 °C Dimensions: (W x H x D) 45 mm x 73.7 mm x 48.6 mm Photoelectric sensor. Energetic proximity sensor. Double marked 7023049. DC 10...30V. Out: 100mA. Complete with manufactures specification sheet. Learn More

SICK OPTIC ELECTRONIC - WT12-P4471 – 1011058 - Photoelectric Proximity Switch, New. The SICK WT12-P4471 (Part No. 1011058) is a discontinued photoelectric proximity sensor. It is specifically designed as a proximity switch with foreground blanking, allowing it to detect objects within a set range while ignoring those closer to the sensor. Status: Discontinued Key Specifications • Functional Principle: Photoelectric proximity sensor with foreground blanking. • Sensing Range: Up to 100mm. • Output Type: PNP. • Switching Mode: Light/dark switching. • Supply Voltage: 10V DC to 30V DC. • Current Rating: 100 mA maximum. • Connection Type: Male connector M12, 4-pin. • Enclosure Rating: IP67 (dust-tight and protected against water immersion). Additional Information: https://www.sick.com/media/productoverview/5/65/765/productoverview_W12_g555765_en.pdf Factory New Learn More

SICK OPTIC ELECTRONIC - WT12-N1421 – Photoelectric Proximity Switch, New The SICK WT12-N1421 (Part No. 1010807) is a photoelectric proximity sensor designed for non-contact object detection. As part of the SICK W12 series, it features a rugged metal housing suitable for demanding industrial environments. Core Specifications • Sensing Range: Adjustable from 35 mm to 100 mm. • Output Type: NPN digital output. • Supply Voltage: 10 V DC to 30 V DC. • Output Current: Maximum of 100 mA. • Connection: Pre-wired with a 4-wire cable, typically 1.5 to 2 meters in length. • Adjustment: Features a manual potentiometer for fine-tuning the sensing distance. Physical & Environmental • Housing Material: Durable zinc die-cast metal. • Dimensions: Approximately 15 mm x 49 mm x 41.5 mm (standard W12 rectangular form factor). • Protection Rating: Often rated up to IP69K, providing high resistance to water and dust. • Operating Temperature: Reliable performance from –40 °C to +60 °C. This sensor is commonly used in packaging, automotive, and logistics applications due to its ability to handle optical interference and harsh physical conditions. Factory New Learn More

SICK OPTIC ELECTRONIC - LUT3-920 - Luminescence Sensor 12-30VDC 100mA out. Sensing Distance: 20mm Wave Length: 375 NM Receiving Range: 450-750 NM Switching Frequency: 1.5 kHX Double marked 1019286. Housing Material: Die-Cast Zinc. Connection Type: Connector M12, 5-pin. UV-LED. Complete with manufactures operating instructions. Made in Germany Factory New Learn More

SICK OPTIC ELECTRONIC - CS1-P3611 – Colour Sensor. Status: Discontinued Q=PNP, Output 12-30VDC 100mA out. 60mm Sensing Distance 5 Pin, M12 Connector Double marked 1012859. Housing Material: die-cast zinc. Connection Type: Connector M12, 5-pin. UV-LED. Complete with manufacturers operating instructions. Made in Germany Factory New Learn More

RED LION CONTROLS - MLPS0000

Key Features

• Item: Panel Meter Accessories
• Connection: Screw Terminal
• For Use With: CUB4, CUB5, DT8
• Accessory Type: Micro-line Power Supply

Input Power: 115/230V switchable 50/60Hz 3VA

0-60 deg C.

Output Power 12VDC 80mAmps

2 hole mounting

Dimensions: 67.3mm x 47.2mm x 32.5mm High

New Old Stock

Learn More

24VDC Manifold Sub Base No. 555K91. Weight: 5 lbs. Body: 3.5 x 3.5 x 7"L. Learn More

4-20mA CONTROLLER 120V 50/60 40-AMP-LOAD-Resistive Input Impedance 500-Ohms 9"x5.25"x3.75" with big black heatsink - UL-listed Learn More

AND NAND OR NOR Controller DPDT-250VAC-4A-500VA DC:24V 4A, 110V 200mA - Total Serier Inductance and Shunt Capacitance have values restricted to values printed on device -=- -=- Power Req:115VAC 3.5WApproved Intrinsically safe by USA-FM[3610] & W Germany-PTB & Austrlia-SAA & Switzerland-SEV, Made in Germany & Twinsburg, Ohio Either used (but no wiring apparent) or New Old Stock & dusty (probably) - either way, it's guaranteed functional by ESI Learn More

slightly used Programmable Controllers Learn More

PROGRAMMABLE CONTROLLER - OMRON C200H-BC101-V2 Base Unit with CPU01 including Memory Unit C200H-MR431. Also Includes 8 Cards:  IA122(3) IM212(1) OC221(1) OC222(3)

Learn More

module- Missing It's Cover Learn More