Other Process Control

Black I/O cover plate. P/N C030046012, ID I8974. Dimensions: plastic 10-7/16" x 1-1/8" deep x 3/4" high. Learn More

32 Point Out 24vdc Source Learn More

Processor rack, augmented. 620-06/10/15 Y904186000006. Size: 19". Learn More

Driver module parallel link. Learn More

Control unit. P/B, twin maintained flush actuators, 1NO 1NC. Learn More

4-20mA CONTROLS 25AMPS @ 600VAC 50/60Hz 1-Phase Input Impedance 500-ohms 6"x4.7"x4"tall built into heatsink Learn More

Mechanical interlock unit for contactor sizes E02 to E4. Used when building a reversing starter, prevents both contactors from being pulled in at once. Learn More

AC Digital Meter 0-2/20/200mA/2Amp or 0-200mV/20/200V SimTach ACDigital Panel Meter 4-1/2-digits, slightly used Adj Zero, Span, Scale - No Instructions included - DP1,2,3,4 "VAC @ 6VA 50/60Hz - red plastic bezel smudged but very readable Learn More

Lite-Pac Trigger Module "LASER TRIGGER FLASH TUBE?" SS TUBE APPROX 1.5" X 4" long wire leads New. Learn More

Photoelectric sensor. Range: 2.5mm adjustable with pushbutton. 4-Wire PNP: quick disconnect with alarm output. 10-36VDC 200/10mA. Additional P/N: OG5046. NIB with manufactures specification sheet. Learn More

Control box. Complete with two counters P/N 53300-400. Input: 15-132VDC. Output: 18-132VAC. More info: http://downloads.eatoncanada.ca/downloads/Specific%20Control%20and%20Display%20%28Durant%29/Instructions/53300-900-08%20-%20Courier%20Model%2053300400,%2053300401%2053302400%20User%20Manual.pdf Learn More

Cutler-Hammer / Eaton - ELC-PA10AADT plus 4 I/O Modules

At less than half the size of most PLCs, the Cutler-Hammer. ELC is an ideal solution when space is at a premium and specialized I/O needs present themselves.

(1)-ELC-PA10AADT: Logic Controller

PLC; 10 I/O

6-In 4-Output Module capacity.

Plus (1)-ELC-AN02NANN: Analog 2-point Output unit.

And (2)-ELC-EX08NNAN Digital Input units, 8-point AC.

Plus (1)-ELC-EX16NNDR Digital I/O 8-In and 8-Relay Out Expansion module.

Original boxes and cables, instructions with Instruments.

Additional Information: 66ed730e5dd7fa35cdbdbdff6fa8ca70.pdf

https://www.eaton.com/content/dam/eaton/products/industrialcontrols-drives-automation-sensors/legacy-page---logic-and-io-legacy-products/elc-modular-plcs/IL05003010E%20ELC-PA10AADx%20ELC%20Analog%20Controllers.pdf

New

Learn More

Cutler-Hammer / Eaton - 6552A-6503 - Cable Accessory.

50/55 Series Cable

2 Conductor

Length: 3 Feet.

Made in the USA.

Learn More

Eaton - Cutler-Hammer - E57-18LU08-D  Switch, Proximity.

Premium Series -Inductive

Output: Normally Open

Sensing Range: 8mm.

Supply: 10-50VDC 200mA.

Max. Load Current: 0.25 Amps

Body Composition: Metallic

Status Indication: LED

Connection: 2-meter 2-conductor unshieded cable.

Body: 18mm diameter, threaded with two nuts.

Non Embedable.

Short Circuit Protected / Reverse Polarity Protection

With Wiring Diagram.

UPC 782113922478

UL, CE Approved.

 

Learn More

EATON - CUTLER-HAMMER - E57EAL6T111SP -Sensor, Proximity.

Tubular 6mm 10-30VDC 120mA NO PNP. Series: A1.

Diameter: 6 mm

Shielding: Shielded

Power Type: DC

Range: 1 mm

Output Type: NO PNP

Number of Wires: 3

Operating Voltage Range: 10~30 VDC

Sensing Type: End

Status Indicator: Yes

Short Circuit Protection: Yes

Max. Load Current: 0.2 Amps

Max. Leakage Current:0.01 mA

Approvals: CE

Cable, 3 Conductor, Rubber Jacket.

Manufacture box is double marked: 78-2113-90872.

UPC:  782113908724

Made in Germany

Learn More

Sensor, proximity. Inductive tubular NO PNP 10-50VDC 200mA cont. Series: E1. Size: 30mm. Sensing range: 7mm. Cable embeddable 300V, 3 conductor. Learn More

Photoelectric sensor body only for E51.10-30VDC source (PNP) 0.6Amp @ 40 DegC. Used/RFE/removed from equipment.

Learn More

Photoelectric diffuse reflective sensor. Series A1. Voltage: 110VAC. Mini 4 pin male connector. Package: metal tube. Manufacture's specification sheet included. Learn More

CISCO SYSTEMS - 73-8545-02 Rev. 07 - High-Speed WAN Interface Card, (HWIC) PWB, New Device Type: It is an internal hardware component, specifically a printed circuit board for an HWIC module used in Cisco integrated services routers. A HWIC (High-Speed WAN Interface Card) slot is a modular expansion slot on Cisco Integrated Services Routers (ISRs) designed for increased data throughput compared to standard WIC slots. It supports WAN connections, serial ports, and Ethernet, offering up to 400 Mbps of bandwidth. They are commonly found on Cisco 1800, 2800, 3800, and some ISR G2 series routers. HWIC Board, Requires Plug-in Power Supply Other PWB Markings: FHH0715001P, 28-6258-02 Contains Pulse H2008 0249-J Chip Installation & Configuration Guides You can find official documentation for this hardware on the Cisco Support Portal. 1. Hardware Installation: Follow the Installing Cisco Interface Cards guide to physically seat the card in an open HWIC slot. Step 1: Power off the router. Step 2: Remove the blank faceplate from the HWIC slot. Step 3: Align the card with the guide rails and slide it in until the connectors seat. Step 4: Tighten the captive screws and power on the device. 2. Configuration: Use the HWIC-4ESW Configuration Guide for setting up VLANs and Layer 2 switching. Note that ports on this card are Layer 2 only; you cannot assign IP addresses directly to physical ports. Instead, you must create a VLAN Interface (SVI). Learn More

HWIC VMS052200EF Boards "Latest Smart Inj" Learn More

Batch Command Controller. For small batch process control. Complement to Bailey's Loop and Sequence Command Controller. New in box with manual. Learn More

Tripoint switch. 5Amp 125 & 250VAC (1/4HP, 125VAC, 1/2HP, 250VAC, 0.4Amp, 125VDC). Mount: Vertical 4 holes with 2.9" centers. Overall unit is 4.0" long x 3-1/3" wide x 6-1/8" high. Note: Ambient Temperature: 60 Deg C. Tripoint. Learn More

Board. Learn More

HI & Lo Limit LEDs - Hi & Lo Limit Deadband & Setpoint Trimpots Learn More