Telephone

Inductor, telephone. 0.20MH Learn More

Inductor, telephone. 0.200MH Learn More

Switch, key. Mount: 2 holes at 56.2mm centers. Dimensions: 21.4mm wide x 69.4mm high. Learn More

INDUCTOR Learn More

Transformer, Two windings (1-5) & (3-4), 87 ohms resistance, 963mH inductance, 200pF coupling capacitance. Learn More

Western Electric - 2578BJ - Telephone Transformers 11-Pin, Vintage New The Western Electric 2578BJ is a specific transformer, a crucial electrical component made by the historic Western Electric Company, known for its high-quality audio and electronic parts used in telecommunications and Hi-Fi, with this model likely being a vintage item for audio enthusiasts or vintage electronics restoration. Key Details: • Manufacturer: Western Electric, a legendary name in American electronics. • Type: A transformer, used to change voltage levels in electronic circuits. • Connection: 11-pin, PCB (Printed Circuit Board) mount. • Significance: Represents the brand's legacy in audio components, often sought after by audiophiles for vintage sound equipment. In essence, if you see "Western Electric - 2578BJ," you're looking at a specific, likely old, but high-quality transformer from a famous tech manufacturer. Genuine Vintage Western Electric - New Old Stock – Rare - No Counterfeits – No China – No Delays – No Disappointments Made in USA Learn More

6-Pin wall jack dual off set RJ 11 Learn More

Connector, socket. Housing gender: receptacle. Contact gender: female. Circuit count: 6. Note: Female telephone socket with an 16" shielded and grounded cable. Learn More

TEL ELECTRONICS - 9-296 15' ft Telephone Modular Line Cord Phone Cable Extension Wire RJ11

This is a landline telephone cord. It is the wire that usually attaches to the back of telephones and then connects to a modular wall jack. It uses what is called an RJ11 connector which is standard for this application. It can easily be used as a replacement or extension cable. There are 4 conductors allowing it to also be used with 2 lines.

Standard RJ11 (M-M) Modular Connectors

Excellent Signal Transmission

Learn More

Connector, socket. Housing gender: receptacle. Contact gender: female. Circuit count: RJ45. Housing material: plastic. Mount: PCB, RA.

Learn More

CISCO SYSTEMS - 73-8545-02 Rev. 07 - High-Speed WAN Interface Card, (HWIC) PWB, New Device Type: It is an internal hardware component, specifically a printed circuit board for an HWIC module used in Cisco integrated services routers. A HWIC (High-Speed WAN Interface Card) slot is a modular expansion slot on Cisco Integrated Services Routers (ISRs) designed for increased data throughput compared to standard WIC slots. It supports WAN connections, serial ports, and Ethernet, offering up to 400 Mbps of bandwidth. They are commonly found on Cisco 1800, 2800, 3800, and some ISR G2 series routers. HWIC Board, Requires Plug-in Power Supply Other PWB Markings: FHH0715001P, 28-6258-02 Contains Pulse H2008 0249-J Chip Installation & Configuration Guides You can find official documentation for this hardware on the Cisco Support Portal. 1. Hardware Installation: Follow the Installing Cisco Interface Cards guide to physically seat the card in an open HWIC slot. Step 1: Power off the router. Step 2: Remove the blank faceplate from the HWIC slot. Step 3: Align the card with the guide rails and slide it in until the connectors seat. Step 4: Tighten the captive screws and power on the device. 2. Configuration: Use the HWIC-4ESW Configuration Guide for setting up VLANs and Layer 2 switching. Note that ports on this card are Layer 2 only; you cannot assign IP addresses directly to physical ports. Instead, you must create a VLAN Interface (SVI). Learn More

HWIC VMS052200EF Boards "Latest Smart Inj" Learn More

Dual 6 PIN Phone Jack [Wall Plate Style] RJ11/12 Jack

Learn More

Western Electric - MA6A - Relay, Telephone.

Vintage New Old Stock

12 PC contacts.

Learn More

Western Electric - 428A - Telephone Accessory.

Dual 3 contacts 3/16" Phone Plug.

Contact Material: Brass

Twin 2 Vintage Patch Cord Plug.

Genuine  Western Electric - Rare - New Old Stock

Applications: Operator's head telephone, chest transmitters, switch boards.

Proudly Made in USA

Learn More

Western Electric - 316M - Relay, Telephone/Teletype.

Package: can 1.7" square x 3.9" high, including 11 contacts and handle.

Note: Marked "Under High Pressure - Do Not Open".

Boxes are marked 100993799 316M 6-74 571.

Genuine Vintage Western Electric - New older stock.

Learn More

Western Electric - 351B - Telephone Accessory.

Phone Key assembly with attached (4) lead switches.

Test plug for the vertical assembly on a 320-series (second generation) XB switch.

Learn More

Western Electric - 309 -  Telephone Accessory.

Single Plu - 3 contacts 3 Conductors

3/16" Patch Cord Phone Plug.

Red.

Dimensions:  3 1/16 x 1 3/32 x   9/32 x 3/8

Applications: The 309 goes into, among others, the 246-type jack. The 309 was used singly, or in jack panels and PBX's that needed high density numbers of jacks, such as the 608A & D cord boards. Rare plug can be used as headphone, mic, aircraft, Ham, patch cord...etc.

New Old Stock

Alternate: TRS 3/16" Collins Patch Cord Plug

Proudly Made in USA

Learn More

Telephone adaptor. Learn More

Waldom/Molex - 43814-6621 - Connector, Dual RJ11 6 Pin (x2) port.

Modular jack 60V 1.5Amp.

USOC Codes: RJ11           

Number of Positions: 6 Position

Number of Ports: 2 Port

Performance Category: Cat 3     

Mounting Angle: Right Angle      

Termination Style: Through Hole              

Shielding: Unshielded   

Current Rating:  1.5 A     

Voltage Rating:  150 VAC              

Color: Black        

Operating Temperature: - 40 C to + 85 C                

Series: 43814     

Contact Material: Tin     

Contact Plating: Gold    

Flammability Rating: UL 94 V-0  

Gender: Female

Housing Material: Thermoplastic (TP)     

Pitch: 1.02 mm 

Product Type: Modular Connectors / Ethernet Connectors

Alternate: 0438146621.

More info: http://www.molex.com/molex/products/datasheet.jsp?part=active/0438146621_MODULAR_JACKS_PLUG.xml&channel=Products&Lang=en-US#partdetail

Learn More

Connector, phone jack. 6 Pin, crimp. Learn More

Connector, telecommunication. Housing gender: plug. Contact gender: male. Circuit count: 10 Pin modular jack. Mounting type: For 10 Conductor telephone cable. Learn More

Telephone, access. 6 Pin modular jack wall plate. Learn More

RJ12 Input to 2 Way Outlet RJ11 Phone Modular Jack Line Splitter Adapter 6P4C Beige.

Easy to Connect telephone adapter is used to connect the line or the single jack of the telephone socket, with accurate signal transmission and clear sound quality for 2 way Outlet.

Durable High quality phone line splitter made of ABS material, non-toxic and harmless, Long Life.

Short length eliminates unnecessary clutter behind the phone and improves signal strength. 

1 Male Plug RJ12 to 2 Female Duplex Sockets, 6P4C RJ11 plug.

Single socket used to connect to line or telephone outlet

Double socket end used to connect 2 devices (Telephone, Fax, etc.)

Durable construction with ABS UL 94-V2 housing and thick gold plating on contacts

Approximate Dimensions: 165X26X21mm / 6.5”x 1.0”x 0.83”

Telephone, Splitter. "Y", Male 6 pin phone connector to 4 pin female out on a 4" pigtail.

Applications: Telephone, Fax Machine, Ooma VOIP telephony unit, Office Equipment.

Alternates: a14122900ux0039, 9SIA623HZ28791, SPM7921066923, a14062600ux0566

RJ11 is an older version of RJ12, and they are the same size. The difference is that RJ11 uses four internal wires (called conductors) while RJ12 uses six. RJ12 is backwards compatible with RJ11, but RJ11 will not work with RJ12.

Learn More