Featured Products

PANDUIT - 100-096-033 - Connector, DIN.

Contact Gender: male.

Circuit Count: 96 Pin / 3 Row.

Mounting Type: PCB, two mounting holes 3.50".

Pin Spacing: Right Angle, Pitch Spacing: 0.100.

Contact Plating: Gold Plated.

Note: DIN 41612 Connector.

Alternate/ Equvalent: TE Connectivity 5650473-5, DIN-96CPC-SR2-TR.

Learn More

PANASONIC WM-034CY - WM-034 - Audio, Microphone Cartridge.

Omnidirectional Electret Condenser Cartridge.

Part Status : Discontinued

Electret Condenser, Omnidirectional 42db +/-3db.

Frequency Range: 20Hz to 16kHz.

Impedance: 2.2K Ohm. (2200 Ohms)

Sensitivity: -62+/- 3dB

Signal Noise Ratial: 60 dB

Voltage: 4.5VDC, Voltage Range: 4.5 to 10V  (Vs)

Current: 800uA.

Output Type: Analog.

Dimensions: Circular 9.7mm Diameter x 6.7mm thick. (0.382" X 0.264")

Through hole Radial PCB mount, 2.54mm (0.100") standard pin spacing.

Termination: Solder Pads.

Applications: Useful for almost any type telephone and other applications.

Alternates: P9992-ND, CTI 42059, YPM-CH022, V79CH

Made in Japan

Learn More

PERKIN ELMER - HGA - Furnace Head for Heated Graphite Atomizer (HGA) Heated Graphite Atomizer (HGA) FURNACE HEAD, an accessory for Perkin-Elmer Atomic Absorption Spectrophotometers (AA). Basically, sample is placed in a graphite tube and a few hundred amps heats the tube white hot to break down the sample to atoms. Light from the AA passes through the tube and sample and the atoms are identified and measured. The tubing fittings are for cooling water and argon gas to prevent the tube from burning. Description: Chrome plated non-ferrous tool metal, brass? - Fit a One Inch Collette, 1/4-20 additional set up points - Fluid injection points - Round set up head with off-center holes, about 3/4" - Opposite round heads are Spring loaded towards each other with guide pins w/ nylon bushings - comes with roll of flex-tubing (maybe 25') for the fluid point - Adjustable handle points perpendicular to each other. Dimensions: About 5" x 5" x 4.5" high. Two Stainless donuts 2.5"OD, 0.87"W with Inside Diameter of 0.778". Black tube 1.1"OD x 1.25" Long with bronze or brass inserts, moveable with knob. Nine SS ports 3mm ID. Absolutely Beautiful piece of instrumentation & machining. Weighs Approximately 3.35 pounds. Factory New Learn More

Switch, pushbutton. Contacts: NO without actuator, makes for unlimited possibilities. Contact Ratings: 10uA 2VDC / 5mA 12VDc. Mech: PCB. Body: 8mm square x 3mm thick, only 1mm travel. 4Leads. Black body, silver self-cleaning membrane. Note: Tactile, snap-action, micro. Digital logic. Low contact resistance of 200milliohm, only 10mSec bounce. Package of 10.

Learn More

Lot of 2 - PESTOLITE - F4T5-BL - Ultra-Violet Fluorescent 4 Watt Glass Bulb.

Fluorescent Black Light bulb appears to be a normal tube but light is almost completely in the near ultraviolet range.

Black Light. 0.63" Diameter x 6.00" (152mm) L, 5.8" L with Four Pins.

Configuration: 2-pins Eeach End.

Average Lifetime: 6,000 Hours

Manufacturer: PestoLite Inc

Model Reference: SK-6

Lamp Type: F4T5 BL

Base: Fluorescent T5

Base Type: G5 Miniature Bi-Pin

Wavewlength: 368 nm

Service Life: 6000 hrs

Fixture Type: Insect Control Device

Ballast Type: Preheat Magnetic

Wattage: 4

Burn Position: Universal

Color Temperature: Black Light,

Color Rendering Index:   Black Light

Application/Use: Insect Control, Nail Dryer, Conterfeit Currency Detection, Mosquito/Fly Trap/Zapper, UV Transilluminator, Copier, Photo-printing machine,shadowless glue curing, Film, Resin plate and other photosensitive materials, Exposure. F4T5BL 4.5W UV Fluorescent Lamp is used for illumination in scientific and medical applications especially suited for diagnostic and microscopy equipment.

UPC: 600300307672

Alternate P/Ns: 15503, S2904, 3000105, 10017, 4-152, BLE-220B, 204140, BL/350, Flykiller, UFL-F4T5/BL, 90450, LF-4054, 6240-00-151-7642, F4T5/UVA, F4T5/BLCE

Package of 2.

Learn More

NXP Philips - BGD102E  CATV Power Double Amplifier Module.

Status: Discontinued

8.5db gain.

40 to 450 MHz Range Power Doubler

Case: 7-pin with Attached Heatsink.

Overall with heatsink 44.6mm wide x 20.6mm high x 13.5mm wide.

Heatsink is actually only 7.9mm deep with 38.8mm mt centers.

Used/RFE, Removed From Equipment.

Alternate: Motorola MHW5185B

Supereceded by BGD502

Learn More

EBM Papst Fan, Axial. 48VDC (36-56V), 5.9 watt 3100U/min (3100RPM). 110 CFM, 54 dBA, 49 PSIL dB, With speed sensor tach-out (3rd blue wire). Housing Material: Aluminum,  5 metal blades, 4" leads. Mount centers: 5-7/8". Dimensions: 4-11/16" x 1.5" deep. (119mm x 38mm) Weight  1.15Lbs. (.52kG) Hall Effect Leads. Used/Removed from equipment. UL, CSA, & VDE Approved. Made in Germany. 

Learn More

PHILCO - HEF4070BP - IC, CMOS.

Quadruple Exclusive- OR Gate.

Logic Type:XOR

Temperature: -40 C to 70 C

Package: 14 Dip.

Package of 10.

Learn More

EBM Papst – TYP 814 - Fan, Axial. 24VDC 0.10A, 60mm x 25mm w/Frame. Fan, Axial. Voltage: 24VDC – Operating Voltage Range: 12-30VDC 11-29 CFM Current: 0.10A. 2.5 Watt Flow: 11-29CFM. Fan: 2 Wire 60 mm Square x 25mm Deep. Ball Bearing Type 7 Plastic Blade. Material: Glass-Fiber Reinforced Plastic Mounted on removable plastic frame (overall 4.674" long), with four holes underneath, 70.2mm (2.767") centers. Complete with finger guard. Weight: 5 oz without Guard and optional Thermoplastic Mount. Service Life: 50,000 Hours Operating Temperature: -20 C to +70C Installation Position: Any Includes EMB 92X1763 Mounting Bracket and LZ28 Fan Guard Note: Brushless Electronic Motor, Polarity Protected. There is a four pin connector on the fan (AMP 1-480702-0 with the red positive wire on position 1 and the blue negative wire on position 2 and an interlock jumper between positions 3 and 4). A mating connector is AMP 1-480702-1 with 350690-1 pin contacts. Genuine EBM Papst - Made in St. Georgen Germany. Approvals: CSA, UL Learn More

Phelps Dodge - ST38-50TNCM - TNC CONNECTOR Male W/ 6733 TAPERLOCK

Learn More

OPTEK - OPL9071 Photologic sensor.

Package: TO-92-size three leads.

Package of 5.

Learn More

OPTEK - OP265 LED. IR, Infrared Emitting Diode, 890nm.

The OP265 is a high intensity gallium arsenide infrared emitting diode (GaAIAs) that is molded in an IR transmissive clear epoxy package with either a dome or flat lens. The small T-1 package style makes these devices ideal for space limited applications. 

• T-1 (3mm) package style
• Choice of narrow or wide irradiance pattern
• Choice of dome or flat lens
• Mechanically and spectrally matched to other OPTEK devices
• Higher power output than GaAs at equivalent drive currents
• 890 nm diodes
• Current - DC Forward (If) (Max):50mA

• Mounting Type:Through Hole

0.050" lead spacing.

Applications:

• Space limited applications
• Applications requiring coupling efficiency
• Battery operated or voltage limited applications

 

 

Learn More

OPTEK - OP245 LED. IR, infrared emitting diode, 890nm.

Type: Infrared (IR) . Optek P/N KL230-00R         

Current - DC Forward (If) (Max): 50mA   

Wavelength: 890nm       

Voltage - Forward (Vf) (Typ): 1.8V

Case: Sidelooker 0.100" Base.

Matched to OP555 PhotoTransistor.

Current - DC Forward (If) (Max): 50mA

Mounting Type: Through Hole

Operating Temperature: -40°C ~ 100°C (TA)

Orientation: Side View - Package / Case: Radial

Package of 5.

 

Learn More

OPTEK - TT electronics - OHD103-00R Hall Effect Sensor, NPN, open-collector output, latching.

These Hall-effect devices contain a monolithic integrated circuit which incorporates a Hall element, a linear amplifier, a threshold amplifier, and Schmitt trigger on a single Hallogic® silicon chip. Included on-chip is a bandgap voltage regulator that allows operation with a wide range of supply voltages. This devices feature logic level output and provide of 20 mA of sink current. This allows direct driving of more than 7 TTL loads or any standard logic family using power supplies ranging from 4.5 to 24 volts. Output amplitude is constant at switching frequencies from DC to over 200 kHz.

• Designed for non-contact switching operations
• Operates over a broad range of supply voltages
• Excellent temperature stability operates in harsh environments
• Suitable for military and space applications

Operates on 4.5 - 24VDC

Output Max 20mA DC.

The latch is reset (off) in one of two ways; by aligning a South magnetic pole with the front face or temporarily removing the bias voltage supply.(off).

The back face has a 45-degree bevel. Facing the leads. with the bevel down, the three leads are numbered 1-2-3 from left to right.

Positive (+) supply connects to pin 1, negative (-) common to pin 2 and the output to pin 3.

The output completes a switch to common when it is "on."

Applications: Non-contact switching operations, Brushless DC motors, Multiple pole magnets, Non-contact reflective object sensor, Assembly line automation, Machine automation, Machine safety, End of travel sensor, Door sensor

Learn More

OPTEK - OHD100 Hall Effect Sensor, NPN, open-collector output, non-latching.

Contains a linear amp and Schmitt trigger to provide sharp "on" and "off" transitions when a South magnetic pole aligns with the front face (on) and is then removed (off). The back face has a 45-degree bevel. Facing the leads. with the bevel down, the three leads are numbered 1-2-3 from left to right. Positive (+) supply connects to pin 1, negative (-) common to pin 2 and the output to pin 3. The output completes a switch to common when it is "on."

Designed for non-contact switching operations

Operates on 4.5 - 24VDC,

Output max 20mA DC.

Operating Temperature: ‐55 °C to +150 °C

New Old Stock

Learn More

Side-viewing optical sensor TO-92-size three leads. No other info avail. Learn More

OPTO 22 - G4OAC5MA  Relay, Solid State.

Control: 5V digital.

Current Rating: 3 A

Input Current: 12 mA

Operating Temperature: -30 to 70 °C

Operating Supply Voltage: 5 V

Output Current: 3 A

Output Voltage: 140 V

Throw Configuration: SPST

Turn-On Delay Time: 8.3ms

Dimensions: Depth 47.5 mm, Length 48.8 mm, Width 12.2 mm

Compliance: UL, RoHS Compliant

Load: 1.5A 12-140VAC with HOA / switch.

Learn More

OMRON - Z15HW4344B7K - Switch, Micro, Lever.

Contacts: SPDT.

Contact Ratings: 10Amp 125/250VAC or 277VAC (1/8HP 125VAC, 1/4HP 250VAC).

Connection: Screw.

Mech: Panel, with two unthreaded mount holes at 1" centers.

Body: 1.941" long x 0.685" wide x 1/162" high with lever extending 0.37" beyond switch body.

Note: Very Light Pressure.

New Old Stock

Learn More

Osram Sylvania - Code 302990 - 2014 - Speicialty Halogen Bulb.

Status: Discontinued

Halogen Clear Quartz

Voltage/Current:/Wattage 14V 2.5Amp 35Watt.

Tubular Shape: T3.25, T3 1/4

G4 Sub-miniature Bi-Pin Base

Base: G4 /GZX4 2-Pin 4mm Center /Center

Luminous Flux (lm): 767

Bulb Finiswh: Clear

Dimensions: 1.562" long.

Average Lifetime 150-hours.

Code 302990

Very Bright - Long Life - High Quality.

Made in USA. 

Alternates: GE 791, USHIO SM-791, BW791, 43123-791

New Old Stock - Rare - Difficult Bulb to Find

UPC 10046135302999

Note: Oil on your hands will damage and/or cause early failure of Halogen bulbs.

Applications: Down Lights, Under Cabinet, Landscape Lighting, Microscopes, Medical, Automotive and Instrumentation.

Highly Discounted for Factory Box of 24 Bulbs

 

 

Learn More

D-Sub Connectors 50-Pin 14.9mm Female straight THREADED NUTDB-50 Panel mount with gold leads approx 9/16" longPanel mount BRASS CONTACTS, TIN SHELL. 1000vac 1Amp Learn More

OK Industries - S9-305S Soldering Iron Tip.

Soldering Iron Tip 0.047".

Double Flat 1.9mm.

For use with K455, K337 Macro Iron Solder Stations.

Learn More

OMRON - EE-SPZ301 - Amplified PhotoMicroSensor with Built-In Amplifier (Light Modulation) PHOTOMICROSENSOR Amplified Light-Modulation Long Distance- Retro-Reflective Dark-On small flange-mounting 1.1" tall plus three leads • Photomicrosensor with light modulation for reduced external light interference. • Easy adjustment and operation validation with an operation indicator (lights when light is incident). • Wide operating voltage range: 5 to 24 VDC • Supports connection with Programmable Controllers (PLCs). • Easy-to-wire connectors assure easy maintenance. Power supply voltage 5 to 24 VDC ±10%, ripple (p-p): 5% max. Current consumption Average: 15 mA max., Peak: 50 mA max. Response frequency 100 Hz Control output: 5 to 24 VDC, 80 mA load current with a residual voltage of 1.0 V max., 10 mA load current with a residual voltage of 0.4 V max. Light source: GaAs infrared LED (pulse lighting) with a peak wavelength of 940 nm Indicator Light indicator (red) Light-receiving element: Si photodiode (Maximum sensitivity wavelength: 850 mm) Ambient illumination: 3,000 lx max. with incandescent light or sunlight on the surface of the receiver Degree of protection: IEC Standard IP50 (excluding terminal section.) Ambient temperature Operating: −10 to +55°C Storage: −25 to +65°C Ambient humidity Operating: 5% to 85% Storage: 5% to 95% Permissible bending Radius of Fiber Unit 25 mm Maximum fiber length Through-beam: 180 cm Reflective: 100 cm Vibration resistance Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 h each in X, Y, and Z directions Shock resistance Destruction: 500 m/s2 for 3 times each in X, Y, and Z directions Cable 2 m max. (Thickness: AWG24 min.) Weight Approx. 3.0 g New - Rare – Difficult Component to Find Made in Japan Alternates: 83F1995, 653-EE-SPZ301A Learn More

OPTEK - KS3175 - Photodiode.

Body dimensions: 1/8" D.

Package: Hermitically Sealed

Domed Lens

Contact: Single Lead,

Pin 1" Gold Plated.

Applications: Non-contact reflecƟve object sensor, Assembly line automation, Machine automation, Machine safety, End of travel sensor, Door sensor

Learn More

OMRON - EE-SY148 - Reflective PhotoSensor.

Status: Discontinued

Transistor Output Emitter and Collector.

Anode & Cathode(K) LED Emitter.

Matched Detector Pairs.

Used for Short Distance Sensing.

Diagram attached for CO Detector.

Dimensions: 5.1mm Thick, 18mm Wide x 15mm Less Leads. 

NSN: 5961-01-176-0009

Alternates: TIL139, 543503138, 143503138, 8139600

Learn More