Featured Products

Hardware, hinges. For cabinets or enclosures. Dimensions: 1-3/4" x 2". Package of 10. Learn More

HARDWARE PACKET with 8 pcs 1 1/2 inch. long #8 philip head screws & 8pcs. #8a speed nut. Learn More

Keystone - PT-237 - Hardware, Threaded Ceramic Spacer. Excellent mechanical strength, chemical erosion resistance, high wear/abrasion resistance and electrical isolation characteristics make these standoff insulators economical and practical for many applications. Material: Ceramic. Exceptional strength in compression and tension. Electrically Insulated and withstands High Temperatures (50 to 1700 F). Threaded for 8/32 screw on one end .50" deep. Radii on all edges. Overall Dimensions: 0.5" OD x 1.25" Long. (12.7 X 31.8 mm). Project Applications: Electronics, Mounting, Isolating. Similar to Cat No. 7670 but threaded only on one side. Learn More

PT-160 Hardware, Grommet.

Material: Rubber.

Dimensions: 0.499" ID x 0.226" thick with an ID of 0.25".

Each side thickness: 0.078".

Color: orange.

ackage of 50.

Learn More

Hardware, Rubber Grommet.

Material: Rubber.

Dimensions: 0.925" OD x 0.50" Thick with an ID of 0.36".

Groove Diameter: 0.625"

Made for an 0.13" Thick Panel.

Package of 10.

Learn More

Keystone – 893 - PT-039 - Hardware, Stand-Offs / Spacer. #8 (M4) Screw. These spacers have excellent wear and abrasion resistance. Exposure to moisture may cause expansion. Material: Nylon Unthreaded, Dimensions: 0.170" Diameter hole x 0.375" Long. Package of 50, Made in USA. Learn More

Vector board PINS teflon Silver plated. Min 4/$1.00 Learn More

Hardware, cable clamp. Closes to 11/16". Mount: Self-adhesive. Color: gray. Package of 15. Learn More

Black leveling foot 1.5" long threaded 1.15" coarse with hard plastic black foot 0.75"diameter - notch at top/bottom Learn More

MAGNET strip 3.5"l X 1.0"w X 1/16" thick Learn More

Hardware. Wire holders. Material: plastic, white. Mount: PCB, snap-in. Dimensions: 0.612" long x 0.220" wide x approximately 0.835" above board. Note: Snap clip. Package of 50. Learn More

Project Enclosure. Two part.

Material: Durable Plastic.

Dimensions: 5.5" x 4.5" x 1.75".

Two long mounting holes, small 1.6" wide access slot in rear 0.3" high.

Color: Black.

Learn More

Hardware, spring. Overall 6-5/8" long. Only 7/8" of which is coiled, 1.2mm steel heavy duty. Both ends curved to fit a 1/4" D shaft or hole. Learn More

Soft/Slightly flexible Magnets 1.25" x 1" x 3/16" thick, with 3.5mm hole in ctr for mount. Min purchase per line item $1.00 = 3/$1.00

Learn More

Hardware, Strap Handle.

Heavy Duty Equipment Handle/Strap.

Material: Plastic/Rubber.

Flexible. Dimensions: 1" wide x 6" long.

With Metal/Zinc Support Ends.

Overall length: 7-3/4" long.

P/N: 00383-91-20008.

NOTE: We do NOT include screw harware for mounting.

Alternate/Similar: Reliable Hardware Company RH-0585-A

Learn More

Hollow True Bakelite Tube/Rod.

Bakelite or polyoxybenzylmethylenglycolanhydride was the first plastic made from synthetic components. It is high resistance which make it a poor conductor of heat and electricity.  Due to its hardness and strength it is widely used in switches, relays and connectors. Bakelite is little used in consumer products today due to the cost and complexity of its production and has become quite collectable in recent years.

Dimensions: 1/4" OD x 18" long, with an ID of 0.140".

Great project material. Widely used in electronics, power generation, antenna or various other industries. Insulate high voltage lines or cut to create high voltage stand-offs. 

Industrial functional bakelite tubes for insulating, mounting, spacing electrical/electronic parts, wiring or assembles.

Material ranges in color from light brown to black with a flat or satin finish.

Vintage - New Old Stock

Package of 4.

Learn More

(M) HEADERS 18 PIN RT ANGLE 0.10" SPACING Learn More

Connector, Terminal Strip / Block, Feed-Through.

5 Position, Single Row.

Dual Barrier

Mount: PCB Feed Through.

Dimensions: 5/8" wide x 1-15/16" long x 3/4" above board.

New Old Stock

Learn More

Unidentified MFG - TS04-12 - Connector, Terminal Block/Barrier Strip.

Circuit count: 4 Single Row.

Tri-Barrier

Mounting Tpe: Horizontal Feed thru PCB mount.

Connection: #4 Screws.

Outside Dimensions: 1.36" long 0.65" wide.

New Old Stock

Learn More

R-T08 - Relay, DPDT, Coil Telephone

Coil Voltage; 24VDC 12MA

Coil Reistance: 2K OHM

Vintage New Old Stock 

30008 W/LEAF Switches

Learn More

Motor, 115VAC, Open C-Frame Fan motor.

Shaded Pole direct drive fan motor.

Sleeve Bearings.

Continuous duty.

Mounting: 2 studs 

Shaft Diameter 3/16" (.1875")

Shaft Length 1.45" D Shape

Laminations 2.4" Square

3 Wire, 2 Speed.

Note: C-Frame motors are mechanically reversible by removing the 2 screws holding the bearing housings together
and reversing the rotor/shaft assembly. Studs can also be reversed to the other side.

Learn More

ESAW - FF-12 - Coaxial Cable, Plug-To-Plug

RG59/U with Each end F-59 Molded Connectors.

Copper Center Conductor

Length: 12 Foot.

Color: Black.

Applications: Digital Video, Antenna, Cable TV, VCR, Satellite, Etc...

Learn More

Empro - HA-30-50 - Shunt, DC Ammeter External. 30ADC 50mV, Used/RFE. The Empro HA-30-50 is a 30 Amp, 50 Millivolt (mV) DC ammeter shunt. Part of the Type HA series, it is designed for measuring direct current by providing a proportional voltage drop that can be read by a meter. The type HA has an insulating base and can be mounted on conductive surfaces. Available in ranges of 0.5 amp through 600 amps with a 50mV output and 1 amp through 600 amps with a 100mV output, the HA is designed for power cable hook-up utilizing the 3/8-16 screws. Status: Discontinued Key Specifications • Current Rating: 30 Amperes (ADC). • Voltage Output: 50 Millivolts (mV) at full rated current. • Accuracy: +/-0.25% 9Standard for Type HA Shunts) • Mounting: Base Mounted • Recommended Operation: For continuous use, it is recommended to operate at no more than 2/3 (approximately 20A) of the rated current to prevent overheating. • Mounting: Features an insulated plastic base for mounting to panels or inside enclosures. The base can be removed for direct busbar mounting if needed. • Dimensions: Approximately 6.0" long x 1.25" wide with a center-to-center mounting distance of 5.25 • Applications: The Empro HA-30-50 is a highly regarded, 30-amp, 50mV DC current shunt designed for accurate current measurement. It is widely used in EV conversions and industrial applications due to its small footprint and precise, reliable performance, often considered an industry standard. Ideal for monitoring, battery systems, and inverters. Note: Used/Removed from equipment. Learn More

Qualtech - BC6165 Power cord. 18-3C (18AWG 3 Conductor).

Hospital-grade power cords have been designed to comply with UL and CSA agencies to insure safe and reliable products.

10Amp 125VAC.

Hospital Grade = Plugs marked with a Green Dot

Unshielded.

Type STJ.

Approvals: UL, CSA

Length: 8 Foot, with Right Angle IEC C13 Connector.

Operating temperature: 60 Deg C.

Applications: Hospitals, Medical devices, Patient care equipment

Learn More