Mounting Hardware

UMPCO - MS21333-77 Hardware, cable clamps.

Aerospace Cushioned loop clamp, 1" ID. Tongue hole type, oil resistant.

Distance from loop center to tongue end: 1.125".

Center to center distance between loop and mounting hole: 0.906".

Overall width: 0.625".

Material: Steel, carbon with synthetic rubber mil grade Mil-R-3065.

Material Thickness: 0.032".

Military NSN 5340-00-922-6300.

More info: http://www.umpco.com/products_pdf/NASM21333.pdf

Package of 2.

Learn More

UMPCO - MS21333-75 - NSN 5340-00-050-2740 - Hardware, Cable Clamps.

Cushioned Loop Clamp, 3/4" to 11/64" ID.

Tongue Hole Type, Oil Resistant.

Distance from loop center to tongue end: 1.0".

Center to center distance between loop and mounting hole: 0.781".

Overall width: 0.500".

Material: Steel, carbon with synthetic rubber mil grade Mil-R-3065.

Material Thickness: 0.032".

Military NSN 5340-00-050-2740.

More info: http://www.umpco.com/products_pdf/NASM21333.pdf 

Price for One Clamp, Discounted for quantity purchases of 6 & 60. 

Learn More

BIRD - 5-1357-3 Connector, Electronic Solder Eyelet, Rivet/Eyelet/Terminal.

Electronic eyelets are flanged tubular metal conductors inserted into a printed circuit board. They make electrical continuity between the circuitry on both sides of the board, and are an attachment point for soldering component leads.

Type: Solder.

Appears to be Silver Plated Brass (High thermal and electrical conductivity)

Metric Dimensions: Outside lip is 6.1mm OD, 2.9mm ID with a shaft 3.5mm round and 6.7mm tall under Lip.

Inch Dimensions: Outside lip is 0.240" OD, 0.114" ID with a shaft 0.138" round and 0.264" tall under Lip.

Applications: Secure High Current Electrical and Ground Connections or repairs to chassis and PWBs.

Chose the proper eyelet keeping the following in mind:
LUF The length of the eyelet barrel under the flange should be 0.020-0.035”/0.630-0.890mm greater than the thickness of PCB(this allows the for the right length after the flange is formed)
ID Eyelet inside diameter should be 0.003-0.020”/0.075-0.500mm greater than the component lead diameter for proper fit of  the eyelet through-hole component lead.
FD The flange diameter should be sized so that it does not protrude out onto other pads or conductors in the vicinity
OD The clearance in the PCB hole should allow the eyelet to be inserted without undue force but, but should not exceed 0.125mm greater than the eyelet outside diameter.

Additional Information: http://www.intl-eyelets.com/short_course_on_electronic_eyelets.htm

Genuine Vintage Bird Electronics Hardware - New Old Stock

Package of 100.

Learn More

Hardware, Rubber Grommet.

Material: Rubber.

Dimensions: 0.925" OD x 0.50" Thick with an ID of 0.36".

Groove Diameter: 0.625"

Made for an 0.13" Thick Panel.

Package of 10.

Learn More

Vintage Phenolic Bakelite Connector, Tie Point/Turret/Connection Board/Terminal/Wiring Strip.

5 Position Dual Row Turret Board

10 Terminals, Double Row of 5 each Turret Board.

Phenolic/Bakelite Fiber Board is 0.100" Thick.

Mount: Chassis Mount

Heavy Duty Turrets are Non-Magnet (Suspect Nickel Plated Brass)

Two 0.150" Diameter Mounting Holes Approximately 1.375" Apart

Dimensions: 2.36" Long x 1.14" Wide x0.46 High.

Vintage - New Old Stock - Bulk Packaged

Proudly Made in USA

Alternate/Similar Compoents: Keystone 15106, 15441, 15111

Applications: Repair / Restoration of Vintage Radio, HIFI, Amplifiers. Project Boards or Electronics Test Equipment.

 

 

 

Learn More

ROBINSON AVIATION - K166-8D Hardware, Shock Vibration Isolation Spring Mount, Metallic Dampener.

Anti-Vibration Compression Spring Mount

0.19" ID Hole.

Spring Supported

Flange-Mount on 1.385" Centers.

Mounting Hole Diameter: 0.138  

Learn More

EDWARDS SIGNALING PRODUCTS - 349 Hardware, Enclosure.

The 349 is a weatherproof Mounting Box is perfect for mounting a variety of Edwards signaling appliances such as bells, horns and sirens. It is made from die-cast aluminum and finished at the factory with a baked sage gray enamel finish.

• Rugged Die-Cast aluminum

• Tapped for 3/4" (19 mm) conduit

• Molded neoprene gasket

• Corrosion resistant finish.

Back Mounting Box.

Construction: Rugged Die-Cast Aluminum 

For Edwards Signaling 340 6" or 10" Adaptahorns.

Color: Gray.

Size 6-1/2 Inch Diameter X 1-5/8 Inch Width

Applications: Fits 6”, & 10” 340, 435, 439D, 5520 Series Bells, Duotronic horn/siren

UL Listed for outdoor use.

More info: http://www.edwards-signals.com/index.cfm?pid=185

UPC: 782640242001

Alternate: Newark 92F6379

Learn More

CAMLOC - 22T01-3-08-2BB - Hardware, Screw Fastener.

Captive screws front mount pan head with slotted recess.

All with Plastic Snap-InGrommet.

Will still maintain positive locking of the fastener under vibration.

Package of 10.

Learn More

Omni Fasteners - 05-340201 - Hardware Screw 10-32, 302 Stainless Steel, Package of 10.

Aerospace Machine Screw.

Description: Machine Screw

Thread Class: 3A

Thread Direction: Right-hand

Thread Length: Between 0.532 inches and 0.563 inches

Fastener Length: Between 0.532 inches and 0.563 inches

Head Style: Binding, Slotted Round Head

Head Diameter: Between 0.378 inches and 0.399 inches

Head Height: Between 0.102 inches and 0.114 inches

Internal Drive Style: Cross Recess Type 1

Thread Diameter: 0.190 inches (#10) (3/16")

Thread Qty Per Inch (tpi): 32

Screw Material: Stainless Steel Composition 302

Screw Material Specification: Aisi assn standard single material response

Screw Surface Treatment: Silver

Screw Surface Treatment Specification: Qq-s-365 federal specification single treatment response

Shelf Life: NA

Applications: Aerospace - Hawker Beechcraft, Textron, Cessna, Boeing, Safran, Goodrich, Lucas Aerospace, Pilatus, and others

Alternate: NSN 5305-00-143-3289 

Package of 10.

Learn More

Rittal Corp - 9581 000 - Large Hinges with Fixing Material. For Enclosure PK 9514-000 & PK 9524-000.

Hinges: For hinged attachment of lids. The supplied drilling template ensures problem-free assembly.

1 set = 2 hinges, 4 assembly screws, 3 polyethylene sealing bungs, 1 drilling template.

Color: Grey - RAL 7035

Material: Polystyrene 

Operating Temperature: 80 C

Approvals: CUL, EN

Made in Germany

 

Learn More

CBO - Hardware, Insulator/Stand-Offs. Heavy Duty.

Material: Brass and Ceramic.

Base mount: Oval with 2-1/4" centers (1-5/8" x 2-7/8").

Dimensions: 4" Tall.

Porcelain Insulator: 1.25" Diameter

Brass Support: 1.625" Diameter

Weight: 1.1 lb.

Applications: High Power Transmitters 

Alternate/Similar: Lapp 14760 & 24114

Proudly Made in USA

Learn More

Mill-Max - 3620-2-32-15-00-00-08-0 - Circuit Board Hardware - Terminal Pin, PCB 10u AU OVER NI, Package of 10.

Product Category: Circuit Board Hardware - PCB

Product: Pins    

Type: Terminal Pin, Edge Mount

Length: 0.356 in             

Material: Brass Alloy, Gold Plated           

Brand:  Mill-Max            

Packaging: Bulk

Plating: Gold over Nickel            

RoHS:  Details

Package of 10.

 

Learn More

Signal Measurement Co. - 106TSP - Adjustable Universal Pedestal Equipment Mount 4" to 8"

This Pedestal Mount can angle, tilt, swivel and extend your holder/device for a better viewing position. This mount swivels 360 degrees horizontally and vertically. It extends 4 to 8 inches (100 - 200 mm) and can be attached to any flat surface. The face plate has an AMPS hole pattern to accommodate most holders, cradles, mounts and car kits.

Features:

• Strong Durable Construction
• 360 Degree Swivel
• Provides a firm installation
• Up to 8“ high with 2” extension.
• Aluminum 0.500" Diameter Extension rod.
• Outer Support Sleeve 1 inch diameter with 0.50” inner rod.
• Allen Wrench with 3 additional set screws.
• Compatible with any holder using the standard 4 Hole "AMPS" pattern.

Specifications:

• Material: High Grade Aluminum Rods, Steel Base Plates, Plastic Sleeves
• 2.50 Inch Diameter Round Mounting Base
• Wingnuts for easy adjustment
• 1/8” Think Steel Face Plate
• Color: Black

Applications: Use in the Car, Home, Boat, Camping, Work bench to Mount Cell Phones, Tablets, Test Equipment, Cameras, Speakers, GPS, Radar Detector, Fish Finders, Gaming, Rear View LCD Monitors, Displays.

Learn More

UMPCO - 1919WDG11 Hardware, cable clamps.

Cushioned loop clamp, 0.688" OD.

Inside loop ID: 0.673 - 0.703" max.

Tongue hole type, oil resistant.

Distance from loop center to tongue end: 1.032".

Center to center distance between loop and mounting hole: 0.799" min to 0.829' maximum.

Overall width: 0.490".

Material: steel, carbon with synthetic rubber mil grade Mil-R-3065.

Material thickness: 0.050".

Military NSN 5340-00-664-8163.

More info: http://www.umpco.com/products_pdf/AS21919.pdf

Learn More

UMPCO - 5340-00-050-2740 Hardware, cable clamps.

Cushioned loop clamp, 3/4" ID. Tongue hole type, oil resistant.

Distance from loop center to tongue end: 1.0".

Center to center distance between loop and mounting hole: 0.781". Overall width: 0.500:

Material: steel, carbon with synthetic rubber mil grade Mil-R-3065.

Material thickness: 0.032".

Double marked MS21333-75.

Military NSN 5340-00-050-2740.

More info: www.umpco.com/products_pdf/NASM21333.pdf

Learn More

HH SMITH/ABBATRON - 8672 - Hardware, Phenolic Spacer/Standoff.

Phenolic resins are found in myriad industrial products. Paper phenolics are used in manufacturing electrical components such as electrical insulators, spacer, standoffs, etc..

Phenolic spacers are made from paper-base, resin-impregnated, heat-cured materials.

High torque should not be applied to these spacers.

Insulating spacer of choice when higher temperatures are encountered than can be withstood by nylon, or where greater strength without cold-flow is required.

Threaded 4/40.

Resin Impregnated, Heat Cured Materials with 130C Max. Temperature Rating.

Dimensions: 1/4" OD x 1/2" Long.

Alternates: 8158, 8159

Package of 100.

Learn More

ALLEN BRADLEY - AB - 871C-N3 - AB - 871C-N3 SER A- Switch, Proximity Nickel Plated Brass Nuts. Package of 2

Genuine Rockwell Automation Parts

Large Hex Nuts 18mm

Nickel Plated Brass Mounting Nut

UPC: 662073675471

Proudly Made in USA

Package of 2

Alternates: GXM3MD2439, 871T-N4, ST02, OP-3052

Learn More

Lot of 20 - 069-3322 – 34WWSP - Hardware, Extra Thick Fender Washers 430 Stainless Steel. For 5/16" Bolts. A fender washer is a flat washer with a larger outer diameter in proportion to its center hole. They are designed to spread the load on thin sheet metal. Interestingly, they are named after their use on automobile fenders. Extra Thick Fend Washer 0.120” Thick Dimensions: 2" OD x 0.343” (11/32) ID Material: 430 Stainless Steel Hardware, Extra Thick Fender Washers 430 Stainless Steel. For 5/16" Bolts. A fender washer is a flat washer with a larger outer diameter in proportion to its center hole. They are designed to spread the load on thin sheet metal. Interestingly, they are named after their use on automobile fenders. Extra Thick Fend Washer 0.120” Thick Dimensions: 2" OD x 0.343” (11/32) ID Material: 430 Stainless Steel Package of 20 • Fender washers offer a bolt or screw a wider bearing surface that will disperse the load weight to a greater surface area and ensure that the nut or bolt is pressed up against a smooth surface reducing the chances the fastener loosening over time because of contact with an uneven surface as well as keeping a fastener from pulling through a hole that is larger than the diameter of the head. • A fender washer though similar in shape to a standard washer the outside diameter is much larger in proportion to the center hole. • Made of stainless steel offers a high level of chemical and corrosion resistance and strength that will outperform and outlast zinc plated fasteners for years without the need to perform costly and time consuming maintenance. • The vast majority of stainless steel fasteners are produced with metals from the austenitic family. Their high levels of chromium and nickel provide tough corrosion resistance and the ability to withstand considerable physical strain without fracturing, albeit at a higher cost than the martensitic varieties. • These Fender Washers are made of Grade 430 Stainless Steel which is Magnetic (Does not contain Nickel) and will outlast washers made of steel or zinc for years to come. Made in USA Learn More

MATSUSHITA - HG2-SF New Relay sockets for HG relays

20Amp 250V

Power relay socket

PCB MT 8-pin

Lead free.

New Old Stock

Learn More

Umpco - MS-921333-71 - 5340-00-057-2904 -Hardware, Cable Clamp. 1/2" - 13/64".

Cushioned Metal, Synthetic Rubber Jacketed.

Mount: 5.0mm hole.Diameter: 0.203"

Material Thickness: 0.032"

Center to Center Distance Between Loop and Mounting Hole: 0.656 inches nominal

Distance from Loop Center to Tongue End: 0.875 inches nominal

Loop Inside Diameter: 0.500 inches nominal

Note: Clamp is actually marked MS21333.

Military bags are double marked 5340-00-057-2904.

Applications: Commerical, Industrial, Engine Wiring Harness

 

Learn More