Other Hardware

Mueller Electric Co - BU-60 series Hardware, alligator clips.

Jaw Opening:     0.310" (7.87mm)             

Current Rating (Amps):  10A       

Material:  Steel     

Plating: Nickel   

Insulation: Non-Insulated  

Color:    Natural

Length: 1.970" (50.04mm)           

Termination: Crimp or Solder

Note: May have a bit of "RUST" from moisture during storage.

Compatible with all shrouded, unshrouded, or retractable 0.16" (4mm) banana plugs, solder or crimp connection, jaw opens 0.31" (7.9 mm) max.

Material: Nickel-plated steel (BU-60). Length: 1.97" (50mm).

Package of 25.

Learn More

Phenolic insulation board,

8 x 3"/ Thin 0.011" / 0.2mm phenolic board (tan/orange) used as insulation / circuit board protection in hand held radios and other items requiring insulation.

Has 6 notches cut out of it, about 1/2" wide.

Package of 25.

Phenolic Insulation Boards Phenolic insulation boards are the most effective type of rigid insulation boards currently available. Phenolic insulation board is manufactured by a process in which a plastic foam forms an insulating core between two flexible facing layers.

Learn More

Motorola - MNT62312B1 Antenna Mounting Hardware.

Aluminum Direct Post Mounting Bracket.

Right-Angle 2-5/8" Wide x 4-3/8" Long with 1 -1/8" Diameter Hole.

Base has with four 1/2" x 1/4" slots

U-Bolts for 1 1/2" Diameter Pipe

Two 2" x 3", U-Bolts Threaded 1/4"-20 with Lock Washers and Nuts,

Zinc-plated steel U-bolts have good corrosion resistance in most environments.

Quality Motorola Product.

Weight: 0.5 lbs.

Note: Commonly sold as an option with various Motorola antennas such as GPS Timing and Tetra Mobile Antennas.

 

Learn More

1 Pair of Telescoping Rack Cabinet slides LENGTH:14" OVERALL LENGTH: 29" Non-Pivoting Solid Bearing WITH HARDWARE Learn More

Black Neoprene Rubber Gasket 0.123" thick x 4.45" Round with convenient hole 1.78" directly in the center of it. We also have a nice black glass filled Nylon Ring P/N 056-5891B, same diameter with 1.7"ID hole, again, Right smack in the center, with 8 mounting holes - 0.425" thick in middle, slopes down to 0.07" thick at edge, available for $2.45 also. Learn More

12-Inch long overall. 8.4" Slide Travel Up to 30-pound Weight Bearing.Set consists of (2) zinc electroplated ball-bearing slides and (4) right angle metal brackets and (x) a bunch of screws. Weighs about 2pounds / set. Instruction sheet said "Concealed hinge flipper door slide." Eurpoean hinges Not Included.

Learn More

Hardware. Wire nuts set/kit. Each kit includes - Minimum 3 wire nuts plus 8 #6 sheet metal screws 5/8" long and 8 tinnerman nuts.

Learn More

Steel tethers, vinyl coated. Overall 35-3/8" hole -to- hole mounting loop and hangar, tough. With clear jacket 0.06" / 1.5mm OD. Learn More

Hardware, magnetic door latch. A heavy duty magnet 1.23" long x 0.36" thick including steel sides, with a heavy duty spring loaded push button 0.3"square that will push your door open when you push on it. I think it would require a mating 1/4" or larger tab on door cabinet, when pushed the magnet pulls back. Dimensions: 3" long x 1" x 0.5" thick. Mounts with two slots approximately 2.7" apart. Note: Spring loaded to push open). Learn More

ANSELL AlpaTec SOL-VEX - 37-175-11 - 15 Mil Gloves, green Nitrile. Size11. Package of 12 Pr.

Applications: Chemical Plants and Transportation, Chemical Processing, Oil Refining and Petrochemicals, Cleaning and Degreasing, Exposure to Chemicals, Solvents, Hazardous Liquids, PVC Cements or Standing Water, Janitorial and Maintenance Work

Gloves, Green Nitrile. Size: 11.

Flock-lined, Straight cuff.

Sandpatch Grip Design.

12 - 13" Length.

15.00 mil Thickness. ANSI/ISEA Puncture Level: 3

Industry Standards: ANSI 0 (Cut), EN388 3101, EN374 AKL, EN374 Micro, FDA 21 CFR 177.2600   

High performance Nitrile - Reliable chemical protection. Reduced chemical burns and caustic exposure. Puncture and abrasion protection. Reduced hand injuries. Cotton flock liner - Moisture absorption, Reduced dermatitis and increased comfort.

Component Materials Comply with 21 Cfr 177.2600 for Food Contact

Marked: For protection against OTTO Fuels.

USDA Accepted. FSN: 8415-01-147-6263.

Package of 12 Pr.

Learn More

Hardware. Cover for a 5/16" round object approximately 1/2" deep x 1/8" D. Nipple to pull it off. Material: plastic, black. Learn More

Picker International - 189564 Hardware, Plexiglass / Acrylic Sheet.

Shatter-resistent or lightweight alternative for glass.

Plexiglas sheet is an excellent electrical insulator with a high dielectric constant.

More Heat thermal shock resisant than glass but also has thermal movement 8 times higher than glass.

Dimensions: 4.5" Square x 0.5" thick.

Clear.

Learn More

LORD MANUF. - 204PHC18-100 Hardware, shock mount.

Size: 3" square.

Mount: threaded 5/16" hole.

Material: rubber and steel.

Learn More

Non-shunted Bi-pin Lamp Holders/Tombstones. Low Profile, Slide-On, Snap-On, or Bolt-On Mount.  Quickwire 18AWG Solid or Str Tinned. For T8 LED Replacement and all T8/T10/T12 Fluorescent lamps, 600V 660 watt. Listed: UL/CSA. Package of 2.

Learn More

FMC - Anaconda Flexcon - Stainless Steel Flexible Conduit, Spiral Interlock, 1 Inch Outer Diameter.

VA single metal strip is loosely double interlock-wound to create an extremely flexible interlocked metal hose.

Rust and corrosion resistant due to chromium content.

Superior durability and strength.

Smooth interior for easy wire pulling.

Extremely flexible for easy installation.

Excellent crush proof qualities. 

Withstand approximately 750 degrees F.

Excellent toughness even to low temperatures.

Good forming and welding properties.

For Dry locations.

Dimensions: 1" D x 15.5" long. 

Contracted length is 12 1/2".

Inside Diameter: 0.850", Outer Diameter of end fitting: 1.075"

Bending radius 4".

Extremely well suited to protect wiring.

Used for heating elements, thermocouples, automotive,communications, robotics, and aircraft industries.

High Quality - New Old Stock - Bulk Packaged

Learn More

Black glass-filled Nylon Flange Ring 4.45" Round with 1.7"ID hole Right smack in the center, with 8 mounting holes - 0.425" thick in middle, slopes down to 0.07" thick at edge. We also have available the matching rubber gasket for $2.45 also, P/N 056-6717B. Learn More

STAINLESS STEEL SCREW Learn More

Hardware, feet. Compression Stem Push-in Rubber Feet.

The stem on these bumpers compresses to fit into tight holes. Push the stem into a hole for quick installation. These foot/bumpers are commonly used as feet on instruments and bench-top equipment to keep them from sliding. They're also good as spacers between sheets of material. Also known as stem and grommet bumpers.

Shape: Round 

Diameter: 0.500", Overall Height: 0.340, Foot Height; 0.165" 

Fits: 1/4" Hole 

Also can serve as a bumper or idiot plug for 0.250" hole.

Material: Rubber.

Operating Temperature: -20 to 180 F

Reduces vibration, isolates and prevents movement.

Applications: Ideal for electronics cabinets, test equipment, enclosures, or projects.  

Package of 24.

Learn More

Hardware. Hose clamp 0.3" ID. Package of 50. Learn More

Hardware, hinges. For cabinets or enclosures. Dimensions: 1-3/4" x 2". Package of 10. Learn More

HARDWARE PACKET with 8 pcs 1 1/2 inch. long #8 philip head screws & 8pcs. #8a speed nut. Learn More

Vector board PINS teflon Silver plated. Min 4/$1.00 Learn More

Black leveling foot 1.5" long threaded 1.15" coarse with hard plastic black foot 0.75"diameter - notch at top/bottom Learn More

Hardware. Wire holders. Material: plastic, white. Mount: PCB, snap-in. Dimensions: 0.612" long x 0.220" wide x approximately 0.835" above board. Note: Snap clip. Package of 50. Learn More