Motors

PACIFIC SCIENTIFIC - E33NRHT-LNF-NS-00  65V 5.1A NEMA 34 Hybrid Bipolar Parallel Stepper Motor

Danaher Motion

Status: Discontinued

Po:176W 5.1A BIPOLAR PARALLEL

1.8DEG/STEP

9.6mm flatted shaft [with threaded hole in end] x 29mmL

STEPPER MOTOR 86mm dia x 128mmD 80mm mounting flange, 69mm centers

Note: One has a Pulley attached

New Old stock 

9 Lbs.

Additional Information: https://www.artisantg.com/info/Pacific_Scientific_Step_Motors_Datasheet.pdf

Proudly Made in USA

Alternate: 10-16976

 

Learn More

Motor, stepper. Hybrid. 35VDC 5.4Amp 1.8 Deg/Step 88 watt 1500RPM. bipolar-Parallel. Sigmax [Flux Focusing increases torque}. Shaft: 9.6mm/0.38" D shaft x 30mm long, 4-lead parallel. Max torque at low speed 500-PPR w/ line driver. Holding Torque: 223-349-oz-in [1.58~1.90nM]. Nema-34, 3.4" square frame. Two MS connectors; 5 Pijn male and an 8 Pin male. Made in the USA. Learn More

PARAMETRICS ZeroMax - 240721 - PARATROL S 3/4HP DC Motor Speed Control

PARATROL S

3/4HP 115/1/50/60Hz

Adjustable speed drive provides a 60:1 speed range from a base speed of 1800-RPM either permanent magnet or shunt wound.

Installation Specifications Included.

About 8.5 x 11 x 4"

14-gauge steel blue oil/dust-tight enclosure, two conduit holes in bottom.

Approximately: 10 lbs.

Made in USA

New

Learn More

MURTEN SAIA - UDR11UJ1RHZ40 - Motor, AC With Capcitor SKU 149477.

Saia-Burgess Controls AG, including the "Saia PCD®" brand, was acquired by Honeywell in 2013.

Timing Motor, Reversible.

120VAC 60Hz 2.5 watt, 400-500 RPM.

Dual Sshaft, 4 wire.

Motor Dimensions: 1.878" D x 0.970" wide.

Shafts(s): 0.125" long x 0.657" long (seated), and the other is 0.165" D x 1.5" long.

Note: Can also be used as a Generator.

Made in Switzerland

Note: Capacitor 0.33uF 400V included.

Learn More

MTS AUTOMATION - MPM892BSG6JY1N - 1HP 230V 3-Ph 3000RPM Servo Motor Motor, Servo. Supply: 230V 3-Phase. Current: 2.6A-rms/Phase Rating: Intermittent 3Ph, S9, Class F. Speed: 3,000 RPM max. HP: 1.05. Wire count: 2 MS connectors. Body Dimensions: 3.35"square x 10"L . Shaft: 0.50"D keyed shaft 1.1"L. 10 lbs Note: EN60034-1; IEC 664-1(1992) MTS AUTOMATION Made in Germany by Antriebstechnik GmbH. New Old Stock Learn More

Motor control, Variable Frequency Drive. Input: 115/230V. Output: 60Hz, 120Hz, 240Hz, 400Hz. Learn More

MAXON - 46.032.032-22.00-125 - Gearhead DC Motor

Beautiful High Torque, Very High Efficiency Small DC Motor.

All Ball bearing construction.

Started turning at less than a Volt !

Approx. 25RPM @ 6VDC, Approx 60RPM @12V

32mm dia x 113mm long plus 17mm long shaft w/flat 6mm diameter.

Made in Switzerland

Learn More

PMI KOLLMORGEN - 00-00917-050 - ServoDisc DC Motor with High Precision Analog Pachometer.

What separates the ServoDisc motor from conventional DC servos is its ironless disc armature. This difference enables ServoDisc motors to deliver a level of performance, in both incremental motion and continuous speed applications, which is not attainable with conventional ironcore motor designs. In addition to performance advantages, ServoDisc motors have a unique compact shape that can be an attractive alternative when solving tight packaging problems.

Type U9M4/U6T with PMI U6 Tachometer.

Horse Power: 3/4HP

Dimensions: 4.4" D x almost 6" long.

Has 1.5" dia attachment to large shaft.

2-wires to motor & two-wires to TachoMeter.

Note: Equivalent Platinum Model U9D-A & U9D-B

Proudly Made in USA

Learn More

135W AC Servo Torque 3.3kg-cm 2.27"D x 4.9"L plus 0.40"D splined shaft 0.6"L Mounts with two threaded holes 2.325" 60mm spacing. Has two 33" cables terminating in a 10-pin Male plug, with mating 10-pin panel mount receptacle, new - probably spares for a machine. weighs 2.8 pounds Learn More

60W 1.14kg 1.66"OD x 4.5"L plus 8mm 0.315" splined Shaft 0.5"LongHas two 33" long cables to a 10-pin connector With mating receptacle, new. weighs 1.7pounds Learn More

2.28"d x 6.5"L 0.388"/9.8mm spline shaft 0.45"L New with long cable to 10-pin Male circular connector and mating panel mount SRON2A21-10S socket. 3.67-pounds Mounts with two threaded holes 0.192"ID 2.35"spacing. Learn More

KLIXON - MRF78EV Thermostat, Thermal Cut Out.

Normally Closed, Open up at an unknown temperature.

Dimensions: 26mm dia x 21mm tall.

Adjustment Stem.

Applications: Automatic Motor Protection

Learn More

Hurst - SP137 - Motor, Synchronous Gear Timing, High Torque

Hurst’s core business focused on instrument grade timing motors and assemblies, stepper motors and controls. Today the business has grown into manufacturing low-cost, high-performance brushless DC motors for many markets, including medical, printing and computer applications. 

Supply: 115VAC 60Hz.

N/P Current: 5W.

Speed: 1/15 RPM.

Torque: Hurst MSM Series.

Direction: CCW. (As viewed looking at the shaft)

Shaft Diameter: 0.185" (4.8mm) , Length 1.0: (26.6mm)

Wire count: 2 Wire Leads.

Mech. Mtg: 3 Holes 2.35" Spacing.

Body Dimensions: 2.4" (60mm) Diameter x 2" (51mm) Length.

HP: 0.188"D.

Applications: Displays

Made in USA - New Old Stock

Learn More

HURST - 3002-030 - MODEL A - 115V 50Hz 20 RPM

Torque: 2.3 Oz-In

REVERSIBLE PM SYNCHRONOUS INSTRUMENT GRADE MOTOR 115VAC 50 Hz. 2.5W

Requires 0.25uF capacitor (and SPDT Switch) between Red and Black, 115/50Hz to Red and Blue CW, Black & Blue CCW.

Drop-in replacement for pear-shaped gear cup motors.

Die Cast Gear Housing.

Learn More

12VDC 4.25W 6-lead Bifilar 15-degree Stepper Model #ABS Part #3007-001 Reduction: DD - Volts: 12DC Step Angle: 15-degrees. Mounts with two holes on 2.38" centers, pear shaped gear cup Instrument Motor 0.125" shaft half an inch long. Some instructions supplied. Learn More

HAYDON - AP35-500C - Motor, AC Timing

A Synchronous electric motor is an AC electric motor in which, at steady state, the rotation of the shaft is synchronized with the frequency of the supply current; the rotation period is exactly equal to an integral number of AC cycles.

Product description: 120 VAC Cam Synchronous Motor Drive. Latching microswitch with a rating of 22 Amp 125-250VAC. Adjuststable Cam Time from 1 Second to 14 Seconds. Synchronous Motor is a Hayden 120 VAC 4 RPM with 2-way clutch unit. Unit also contains a 120 VAC DPDT Relay 5 Amp Contacts. 

1 - 13.8 seconds.

Supply Voltage: 120VAC 60Hz 5W.

Haydon Synchronous Motor Speed: 4RPM, 5W E15450 A2396A4.

Mechanical Mount: Panel Mount Frame on 2.8" Centers.

Unit is Complete with Relay, Motor, and SPDT 15Amp Microswitch

Connections: Octal 8 Pin Socket.

UL CSA Approved

Proudly Made in USA

New Old Stock

Learn More

General Instruments - GI-29005-13 Motor, AC.

This AC motor replacement is ideal for someone who requires a powerful source of energy for an extended period of time. The shaded-pole motor is the original type of AC single-phase induction motor, dating back to at least as early as 1890. A shaded-pole motor is a small squirrel-cage motor in which the auxiliary winding is composed of a copper ring or bar surrounding a portion of each pole. The construction of the motor is very simple because it does not contain any commutator, brushes, collector rings, etc. or any other part. The shaded pole induction motor does not have any centrifugal switch. Thus, the chances of failure of the motor are low.

Shaded Pole Motor

Supply: 115V 60Hz 0.5A.

RPM: 3375

Wire Count: 2 with Quick Connect.

Turns CW looking at the shaft.

Mechanical Mounting: 2 holes 1.9" Spacing.

Body Dimensions: "Pancake." 2.5" x 3" mounted on versatile and removeable triangular mounting plate.

Approximate Overall Dimension Including bracket: 4.6" L X 3.8" W X 3.0" D

Shaft: 0.18" Diameter x 1.2" Length.

Wire Lead Length: 20"

Enclosure: Motor Enclosure Design Open Air-Over

Great fan for cooling or other continuous duty operation.

Motor Mounting Position All Angles.

New Old Stock 

Learn More

42mm dia x 14.5mm thick, 2.9mm shaft 11mmL with 6.2mm 10-tooth brass Gear 4-hole plate, 35mm centers Stepper Motor 4-Wires, 19"long very thin 3.6oz Learn More

Motor, DC. Precision PM DC. Made for Gould Brush Chart Recorders C282101. Dimensions: 1.022" OD x 1.230" high. Shaft: 0.079" (2.0mm) D x 0.379" (9.6mm) long). Seated 0.560" (11.7mm) long, from body. 2 Wire, 4.5" long. Learn More

DISC INSTRUMENTS - Honeywell - PC62D-40-5 OPTICAL ENCODER

Made in USA

Used / As removed from Equipment

Learn More

6VDC 1.25Amp 1.8degree 4-Phase 6-teflon 15"wires Stepper Motor 2.25"D x 3.0"L 4-hole mounting 1.85" spacing 0.25"D shaft 0.75"L New, Old Stock weighs 2-pounds Learn More

Danaher Controls – Dynapar - HA62509000101 - Encoder 3/8 SHT FLG MT 5-26VDC SD MT- New Description The Series HA25 is a rugged and reliable encoder for industrial motion applications. The proven design can be the mainstay for any automation project. Mechanical / Electrical Attributes Shaft / Bore Size (mm): 9.525 Connection Location: Radial Disk Material: Glass Flange Material: Aluminum Maximum Operating Speed (RPM): 6000 Connection Type: Connector Termination: 7 Pin MS Connector Shaft Type: Shafted Shaft / Bore Material: Stainless Steel Resolution (PPR): 900 Line Driver Type: 7273 Output Signal: Open Collector w/ 2.2K Ohm Input Voltage: 5-26 VDC Incremental Signal Format: Format A: A Leads B CCW; Index Width (180°) Gated to B' Reverse Polarity Protection: Yes Duty Cycle: 45-55% Short Circuit Protection: Yes Maximum Frequency Response (KHz): 100 Incremental Signals: A Environmental Attributes: Hazardous Area Rating Certification {[None] Minimum Storage Temperature (°C): -40 Noise Immunity Testing Specification: EN61326-1 Hazardous Area Rating: {hazardous_area_rating_certification=[None] Shock Resistance: 50G Humidity Non-Condensing (%): 98 Minimum Operating Temperature (°C): 0 Vibration Resistance: 20G Housing Protection Level: IP66 Maximum Operating Temperature (°C): 70 Maximum Storage Temperature (°C): 90 ROTARY ENCODER 3/8 SHT FLG MT 5-26VDC SD MT DYNAPAR HA62509000101 / HA62509000101, Factory New, INCREMENTAL ENCODER, SHAFTED ENCODER, SERIES HA25, SIZE 25 ENCLOSED, WITH SHAFT SEAL, GLASS DISK, 0900 PPR, FLANGE MOUNT, 3/8" SHAFT, 7 PIN MS CONNECTOR OR CABLE, SINGLE END, W INDEX, 5-26V IN, 5-26V OC W 2.2 KOHM PULLUP OUT, SIDE MOUNT CONNECTOR Made in USA Learn More

Motor, timing. Supply: 24VAC 50Hz. N/P Current: 2.7W. Speed: 1/2-Rev / Hour at 50Hz. Wire count: 12" teflon wire leads. Mech. Mtg.: Two mounting tabs 2.17"spacing. Body Dimensions: 47mmD x 33.7mmH. Shaft Dimensions: 0.25"D flatted shaft 0.5"L. Weight: 6 oz. Note: TYPE 117 Runs 20% Faster on 24V 60Hz. Learn More

Circuit breaker. Motor circuit protection 3P 15Amp 600VAC 250VDC. Style 6601C87G05. Push to trip. Eight adjustable trip settings 45 - 150Amps. Mount: Panel. Dimensions: 4-1/8" wide x 6" high x 3-3/4" deep. Used/Removed from equipment. Learn More